|
-
Feels alright to me, in any case i've sold it now after wasting 12 months of my life building it. Hey Ho
-
Shortens the wheelbase slightly to 50"
-
And at long last Success!!! The Combination of a Rooster Booster ignition, a new stator bush, a massive ammount of faffing and a fresh properly gapped plug and we have a winner.
Finally got there!
Video Link Below - I think the rattle/buzzing is the exhaust hitting the frame - needs insulating
Cheers
Chris
-
Right a bit of an update finally, she's alive!!
After very ponderous progress i went mad and bought a load of bits at Stafford Classic show, a proper Bantam kickstart, Tank badges and ally rear mudguard.
After some careful (guess) work on the timing she fired 2nd kick and ran properly on the 4th.
She has now decided not to start again but it was a momentous occassion and several cold beverages were drunk!
Latest problems in the long list including a slightly bent timing end on the crank, as well as not being able to start it again include a leaky head gasket, leaky exhaust collar and the fact that having taken the clutch cover off to try and stop it leaking i found the clutch basket has next to no teeth left on it, like sharks teeth, having tried to put it into gear the primary chain just buzzes.
New clutch basket sourced so we should be ok
Ah well onwards and upwards
Will post some more pictures when it's done
Cheers
Chris
-
I gave up looking in the end and bought a proper folding trials bantam one.
I went through just about every box at Stafford Classic Show and didn't find anything that would have worked sucessfully.
New one is perfect, doesnt slip and works a treat. Even better than that i finally got it fired up!
Albeit briefly, now the flippin' thing won't start again.
Time to double check the timing i think
Cheers
Chris
-
Hi All,
Project Bantam is coming along very slowly.
I'm now looking for a 3rd Kickstart after the first 2 i made failed.
I've seen several pre65 Banatms with spangly folding kickstarts (usually off other bikes).
Anyone got any ideas as to what fits?
I'm struggling to find a 3/4" splined version of anything
Cheers
Chris
-
Looking good Mikey, hope your not too bad after your off.
Progress is slow at the moment but i've done a bit more
Due to teh lack of offset on the TS50 forks i've had to move the tank back a bit
Rear Tank Mount
Footrest bracket done, just needs final fit
Seat Base made
Now looking a bit like this
Cheers
-
Hi All,
Thought i'd up date the thread with a couple of piccys of progress so far.
Started with this
and this
Got these
and this
a bit of blasting and painting
and a few bits and we're about here
Still a way to go but i'm chuffed with the progress
Cheers
Chris
-
Hi All
Plodding along with my Bantam build, finally got a chance to put her up on her wheels and i've hit a bit of a problem with the sprocket alignment.
The rear is a Bultaco wheel and there is no way of moving the sprocket closer to the hub without some serious machining so my question is can you offset the front sprocket?
It is a D7 engine and whilist i haven't managed to measure the difference accurately yet i estimate it is about 5-6mm too far in.
The other option is to move the engine over in the frame but the exhaust is already virtually touching the frame down tube.
Many thanks in advance
Chris
-
Cracking pics, many thanks.
I now have a TS50 front end, taper head bearings and material to turn some bearing cups and a Bultaco Alloy rear wheel and brake.
A Bitsa and a half i'm sure you will agree
Frame, swingarm, bars and yokes are being sand blasted today hopefully so i should have a semi rolling chassis by sometime next week.
Forks need a little prep work but it shouldn't take too long.
A quick question if i may, whilst in the future i will probably go down the electronic ignition route, what's the best way to run a Bantam, spark only as i'm not worried about lights.
I have the a stator "star" with coils but no stator plate or points etc.
I was thinking along the lines of junking the lighting coils, replacing the ignition coil with a modern replacement and then getting a Rooster Booster to give me a spark.
Does this sound feasible?
Cheers
Chris
-
Thanks for all the pics and info guys, went to the show yesterday and picked up a couple of bits.
Will be making a proper start shortly, i have a TS50 front end on it's way.
I'll post some progress pictures up soon if thats ok?
Cheers
Chris
-
Hello all,
Been having a nosey round this awesome corner of the forum for some inspiration and advice.
As a direct result of my mate Petorius' purchase of a Tiger Cub project i am now the proud owner of a Bantam project.
I'm not new to the world of bikes (i'm on 6 and counting) and projects but i am somewhat new to the world of trials and in particular pre 65.
The sorry looking pile of parts currently consists of a D3 1956 swingarm frame, a 1959 D7 engine, a chrome tank, and not a lot else.
One thing i have found is a casting on the underside of the head "GT100B", i was led to believe that the engine had a Todd centre plug head, i was wondering if this casting corresponds? Are these heads rare?
The aim of the project is to build something i can have a bit of fun on without getting bogged down in historically accurate details and mega bucks parts.
I have a lot of questions but i was wondering does anyone have some basic guidelines to get me going?
I've looked at a few posts around the swingarm width and modifications, using a 4.00 x 18 tyre etc.
I think it will probably be a "modern" front end, TS50 or the like. What sort of shock length would i be looking for?
Please forgive all my questions, i'm really looking forward to falling off very soon!
Cheers
Chris
|
|