oneal121

Hi all, i need a little help a long story short my radiator cracked on my JTX 250 and had to be repaired. I've refitted the radiator but i cant seen to get the wiring routed right and the tank doesn't seem to sit right. So my question is does anyone please have a picture or pictures that you can post of how the wiring harness is routed laid out.

I have a 97 jtx 250, the first job i did with mine was to change the clutch fluid, mine takes dot 4 brake fluid and then check the adjustment on the lever if your not sure how to do this go on to you tube and search jim snell gas gas video channel. I also run 650 ml of mineral gear oil MTF 94 i think it is. And it also made a big difference on how the clutch behaves. I also run my pre mix at 70ml per 5 liters of fuel. It would also help if you cleaned out the exhaust center box while its leaking and seal the joints hi temp copper based silicone sealant and make sure the o rings are in good shape. Hope this helps some what.

it was interesting to see who did and didn't use evans. And the reason why, i know trials is a misers sport by the people ive spoken to since ive been involved with club trials.

Just wondered how riders run there gas gas trials bikes on Evans Coolant rather than just antifreeze mix.

Here's my old girl when i picked her up a 97 JTX 250. lots of work later she's looking good and rides brilliantly.

Thanks for the info thats a five, does anyone have a link to a workshop manual as gas gas themselves only have the parts books.

cheers for the info, the new cable as now been fitted run up the left of the frame and around the head stock. And everything feels good

I had a husky 250 that had the same type of problem, for me it turned out be the ignition coil dying when it got hot and started to breakdown and the bike would die.

Hi all, i need a little help my new to me gas gas jtx 250 as had a few minor problems. The throttle cable looked to be routed wrong running up the right hand side of the bike and out through the front of the frame with a big loop behind the number board. Can anyone please let know the correct throttle cable route. Also should the correct spark plug should it be a BPR5ES Or a BPR7ES as im getting conflicting information and my old spark plug is unreadable. \Thanks for any help in adavance

Hi all, I've managed to sort out my forks they where sticking at the bottom of the stroke when the forks was compressed. I have stripped them down and cleaned them out, the fork oil was like sludge. So after a good clean out and fork oil change everything seems to be ok. If the rest of my spares turn up I be giving her a try out at the weekend.

Hi all my new to me beta rev 3 250 has a few issues, as anyone had problems with the front forks sticking or just generally locking and not moving. what's the best way to get it sorted I don't mind servicing the forks myself its just a bit of a weird one. Can anyone confirm if the rear shock bearings are BLRB366748AA as i'm struggling to find a good local supplier who has them in stock. Thanks for any help its a appreciated.

classic 90's tune and a good find on the video.

Have you checked the air boot from the carb to the air box mine had the same type of problem. Mine had dry rotted and split up to the air filter box.

While doing the maqintenance on my sy 250 i changed the gear oil and while the oil looked fairly fresh, but not knowing when it was last done i changed it anyway. The oil coming out was bright green anyone know what this oil was ?. I always use rock oil products but im just curious as to what the old oil was.

Ive just done Dan's mod to my Beta Techno And i was amazed on how much glue build up that there was on the fibre plates. And while i was in there i changed the oil for rock oil lite gear oil and the results are great. I can now get neutral and no drag and no jumping when put into gear.

Hi all, Just a couple of quick questions regarding my 1998 250 techno. what gearing is stock, im currently running 10-43. The second one is the topend seems a bit flat she pulls really strong and then just seems to run out of steam is this normal for the techno. Also is there any good set ups tips which i should know about for the techno.

If you needs parts fast try trials and tribulations they have a good selection of parts online. The bike looks very much like mine so im sure its a 03 model, as for the the rear shock bush try taking the bearing out and going to your local bearing shop they should be able to find you a match. Sorry i cant help much with the plastics but again ive seen them on the trials and tribulations site. See you on the orange side.

Hi all i have a 03 sy 250 that needs the clutch fluid to be replaced, i'm just wondering what is the correct type of fluid to use.

Good morning all Im new to the trials scene and ive just got myself a scorpa sy 250(03) in really good nick. Im based in northamptonshire. If anyone knows of anywhere to practice or sign to events please let me know. Im a noob when it comes to trials but ive ridden Mx, enduro and H&H for many years Id just like try something new.