Jump to content

mickmc

Members
  • Posts

    101
  • Joined

  • Last visited

Everything posted by mickmc
 
 
  1. Hi does anyone know what the number for the main bearings in a Beta evo 125, also the seal number and sizes, its so I can go to my local bearing company, thanks in advance Mick
  2. Hi, I am changing the kickstart spring on a beta 80, I have drained the oil and the coolant, can I take the cover straight off without taking the water pump cover off, any information on this appreciated, thanks
  3. hi does anyone know the settings for a beta 80 2006 delorto carb, thanks
  4. Hi Does anyone know the make/type and sizes of the main bearings for my Beta 80 rev it's a 2006, I know I can get them from beta uk but looking to buy direct from a bearing company also the crank seals sizes thanks in advance
  5. hi, we have a problem with our beta evo 125 2013, it got stuck in gear and won't release at all, has anyone else had any problems,or know how to fix it, assuming its a big strip down? thanks Mick
  6. I have a beta evo and having problems with the front brake, I have noticed that 2 of the pistons are not coming back out of the caliper, so deciding to rebuild it, does anyone know how to do this cheers
  7. hi, what is the best way to clean the centre pipe, as mine is well gunked up inside, thanks in advance Mick
  8. when I was changing the seals on the waterpump, the impeller was broken in pieces, but the shaft looks ok but was further inside the engine because the impeller and circlip wasn't holding it out, would this be normal, or might it have done some damage I can move the shaft in and out slightly (not taken it out) and does turn round freely hope you can understand what I mean , what do you think cheers
  9. hi the fan stopped working today on our beta evo 125, i don't have a voltage tester so could i test it with a car battery, to see if the fan is working and that it isn't the thermostat, would that be the correct voltage ?? thanks
  10. Thanks for your replies, all very helpful, now have them out and also repaired this morning
  11. hi i have been trying to take the forkseals out of the stanshions, the top seal came out quite easy but i am having problems getting the bottom seal out on both of the stanshions, and have broken pieces out of the tops of both stanchions, has anyone got any ideas how to get these out without further damage, and also do you know any good repairers please thanks
  12. just want to say a big thank you to all the organisers and observers and marshalls, for a fantastic trial, shame Kieran is too old next year, and didn't quite complete it but did better than he did last year.
  13. hi thanks for your reply, it is helpful, if I head into ilkley itself, (coming from Leicester, down south) is ilkley bridge easy to find, according to the entrance form, it should be signed from there, but will write down your directions, many thanks and well done on your achievement, Mick
  14. hi, we are taking part in this on saturday, well my son is, does anyone know of a post code or pub? near to the start of the venue, having never done this before not entirely sure where to start, also not been to ilkley or that area before, cheers
  15. hi thanks again, thats great
  16. wow that is brilliant, thank you for that, meant to put my bike is a 125 would it be the same level for all the evos, cheers
  17. Hi i am changing the fork seals in my beta evo 2013, could anyone tell me the level of the oil or amount of oil to put in each individual leg, thanks in advance Mick
  18. does anyone know how to clean out the rear part of the exhaust on a fantic 200 standard original exhaust any help or advice appreciated
  19. Hi, can anyone tell me the part number for the bearings (the dog bones, suspension bearings) also do you know supplier to get them from, many thanks Mick
  20. would it be ok to put a tube in a tubeless tyre ????
  21. hi hope someone can help, just need to know what the measurement of fluid for each leg please, of the Beta 125 Evo 2013, standard bike not factory are the seals easy enough to replace, have done the gasser in the past, thanks in advance Mick
  22. hi just wanting to touch up the paint work on our gasgas 2011 red frame, and wondered if anyone knows the colour code or where I can get one close as possible to the colour, any help appreciated, thanks
  23. do you know what size o rings to replace with ....just in case, because we have to buy either a replacement kit for £25 (that wouldn't fit) or a new cylinder, can't get hold of the o rings, in the UK that is shouldn't have to work on the cylinder should be 'fit for purpose' and certainly last longer than 6 months
  24. hi, i'm on my third master cylinder and previously replaced the first one with 2 replacement kits, but gas gas don't want to know and I've had to pay for these myself, the bike is only a 2011 so only 2 years old . the second master cylinder lasted just over 6 months at a cost of over £100 each time, my lad has missed trials or had to drop down to easier route because he had no back brake, I have been told the problem is it has a bur inside the cylinder where the piston goes up and down, then that causes the rubbers to split, so would need to file this out with needle file, then put new replacement kit in IF you can get one that fits, the replacement kit I just bought doesn't fit the second master cylinder so just had to buy brand new master cylinder, and can't get a refund on the replacement kit because I had marked the end bit trying to get it out, if I knew it might not fit I wouldn't have put it in, also been advised to keep an eye on the brake fluid and replace it regularly to get the dirt out ,could be the dirt causing problems has to be a design fault, something definitely wrong with so many of us having problems!!! have a son with a smile now that I've replaced the cylinder again, bled the system, and now have a back brake ready for sunday lets see how long it lasts, the smile ...and the brake
  25. gas gas 125 2011, if anyone could recommend a good repairer, Leicestershire area, let me know please first time out in weeks after having the frame welded, now hole in radiator, our luck doesn't seem to be with us, what next!! have put a wanted on the adds just in case it's not repairable, hoping it is though
 
×
  • Create New...