Jump to content

rodt

Members
  • Posts

    40
  • Joined

  • Last visited

Contact Information
 
   
Recent Profile Visitors
 
 
5,986 profile views
 
  1. You are right about the payment for results. I don't know about Nationals but Centre Trials were £10 for a win and £5 for Novice award. Ian Haydon was quite successful in the South West Centre on a Torbay Motorcycles Kawasaki KT 250 around 75,76
  2. Are the lights on all the time ( no on/off switch, just dip) If so it sounds like the feed wire to the dip switch has a bad connection or the wire is broken. For the MOT if push comes to shove you can cover all the lights up and get a day time MOT.
  3. I think that might be Paul Dunkley as the front number plate is on the mudguard, not accross the forks. Not many did that. Must be 1970/71. I have no idea where it is.
  4. rodt

    Fantic Wheel

    That was a quick reply. Thank you for the info.
  5. rodt

    Fantic Wheel

    I have a rear wheel which I think is from a 240 Fantic. Could anyone confirm this or have an idea as to what it is from please. Thank you.
  6. rodt

    Beta Alp 200 Gearing

    Thank you for the information.
  7. rodt

    Beta Alp 200 Gearing

    Hello, I have just bought a 2002 Beta Alp 200. Could anyone please tell me what size sprockets they use for Trials use (LDT) and road use. Many thanks.
  8. The only shims on the crankshaft would be the Big End Crankpin thrust washers
  9. Google Yamaha TTR 125 wiring diagram and you will find a pdf Yamaha manual, which has a wiring diagram . Seeing as the motor is a TTR 125 that might well help. I couldn't get it to link to this page.
  10. If it has the original wipac round coil in the stator plate, remove the HT lead but leave the low tension side connected to the points. Run a wire from the points to a Japanese 6v ac coil, put that under the tank. Fully advance the stator plate, set the points gap at 10 thou and bend the points spring a bit to give it more tension. Fit a new condenser. I used a 6v dc coil and battery on the D7 Bantam I had. It was a lot better with that set up.
  11. rodt

    When Was This?

    That bike looks like the works Bultaco that Malcolm Rathmell won the last European Trials championship on in 1974
  12. To the best of my knowledge that method of marking was used in Ireland. Early post war marking was 3 for footing ( dab or paddle ) and 5 for a stop. 1 mark for a dab came in in the mid fifties and remained as 1, 3, 5 until early 70's, 73 ish when the 2 for two dabs came in. Didn't make much difference to me when I started riding in Schoolboy events in 72 on a £15 D1 plunger Bantam as best I could hope for was a 3
  13. Hello. Sometimes it is a bit of grit or dirt in the seal and can be cleaned out using a film negative. I have done this with success. Certainly worth a try before stripping your forks. if you're really keen you could buy one of these !! http://www.ebay.co.uk/itm/Seal-Mate-Tool-Sealmate-Fix-Leaking-Fork-Seals-Quick-Easy-Fast-Affordable-/121059312192?pt=UK_Motorcycle_Parts_13&hash=item1c2fb28240
  14. I have a Scorpa TYS 125 and I am more than happy with it. It struggles in muddy conditions but I put that down to operator error There is one on Ebay at the moment. Right money I would say. http://www.ebay.co.uk/itm/2004-SCORPA-TYS-125-F-BLUE-WHITE-Trials-GasGas-Sherco-Beta-Montesa-/151498431709?pt=UK_Motorcycles&hash=item2346029cdd
  15. Fantastic video from a classic No stop era, when you only used the clutch to put the bike in gear
×
  • Create New...