Jump to content

andyj007

Members
  • Posts

    35
  • Joined

  • Last visited

Contact Methods

  • Website URL
    http://www.adjconstruction.viewbook.com
Contact Information
 
   
  1. As it says, dropped on a new barrel and piston in the tlr tonight, got it all back together and fired up.. Sounds lovely, admiring my handy work with bike purring in background and notice on the old head where barrel meets bottom case that I dowel pin stayed on old head. Looking through manual, it appears there should be three of them. So probably my only has two now.. Any one tell me what exactly they do? And if I can leave it for a while with no risk of damage?... Cheers.
  2. Super cool awesome work. Cheers for posting up.. Love your vids
  3. andyj007

    Tlr 200 Noise

    Hi again.. I'm just about to tear into the top end to replace the valve stem seals. As suggested in my other thread. Whilst I'm in there It would be sensible to check all possible. Engine runs lovely just smokes white/ bluish until warm. I have noticed that after just starting from cold the engine is really quiet and develops a ticking/knocking noise as it gets warmer I assume because the engine oil gets thinner so can't suppress the noise. Any suggestions what it could be or is this normal? Ta Aj
  4. Got to reply to that.. nice job, got some good height there.. the curse of the video eh!
  5. andyj007

    Bar Rises

    Hi guys got a 250 2998, I'm 6ft, going to rise the bars up as I feel that I'm loading the grips too much under normal standing position. I have a tlr 200 Honda and I love that position. The bars are about 80mm higher and the foot pegs 30mm higher, so I make that a foot peg to bar about 50 mm. I'm thinking of getting some rises made for about 40 or 50 mm. This seems like a lot. What do you tall guys run.. Ps had my second tral today what a top bike I love it. Cheers
  6. Which is best? Is it worth the extra getting the workshop manual from states for my tlr 200? http://www.ebay.co.uk/itm/Honda-XL-XR-TLR-125-200-1979-87-XR200R-03-4th-Clymer-Publishing-New-/140732453120?pt=Non_Fiction&hash=item20c44ed100#ht_1832wt_1008 Or http://www.ebay.co.uk/itm/New-Service-Shop-Repair-Manual-TLR200-Reflex-OEM-Honda-Maintenance-Book-N92-/360447238286?pt=Motors_Manuals_Literature&hash=item53ec54608e#ht_4021wt_689 Thanks
  7. hey bernard thats a sup[er looking TLr, did you restore/modifi it your self? do you use it regular in trials, how do you get on with it.. any more pics? kind regards Andy
  8. you sure this is not the floating front disc. bounce it without the front brake on.... regards andy
  9. THanks for the reply, just got in from the garage. it looks like a combination of two things. one the gearbox was short on oil!.... and had run all to one side leaving the clutch side dry... replaced & drained twice... removed the exhaust and a large amount of black petrol ish liquid drained out...probably a cupfull... most evaporated sop was fuel.. piston lookes good through exhaust port.. hoping that the very low oil has nt damaged the engine... all sounds and runs sweet.. cheers...
  10. Guys help... Was just prepping lads and my bike for tomorrow. The beta rev 50 is really tight / stiff to kick over. Really tight. it will turn over but is tight. Bike was fine when put away, and has just sat for three weeks on side kickstart. Did wash the bike before putting away, but this was a light was and was started and run afterwards Any suggestions much appreciated. Ta
  11. i have been told that most cheaper aftermarket seals use nitrile rubber, the oe parts are viton.. a far superiour material for this use... therefore if the ebay ones are viton they may be ok.. i have just ordered all original honda parts to be on the safe side it was only a few extra pounds anyway.. cheers andy
  12. The engine had a full rebuild two years ago and a ring and noisy bearing done recently. The previous owner does not know if they were replaced then or not. So let's assume not. He's still digging all the receipts out for me. I will order the gasket set and genuine seals tomorrow. I can't see it carb related as its a white blueish smoke, and smells like its oil. Carb/ air filter issues normally on four stroke make running rich therefore I would expect discharge to be black smoke...correct? Will have a read of the manual tomorrow. Cheers
  13. More piccies please. White frame looks tops, How long did it take you what else did you have to do Cheers
  14. Cheers. for the reply . a good place to start then. will it be ok to use in the meantime? or is it causing damage? i will have some spare time in a few weeks but would quite like to get out on a few trials first.. is it possible you could list all the items required for this works.. whilst i can use a spanner I think i may just get all the parts and get some assistance . I have a manual, and whilst my mechanical skills are ok, I strip and rebuild forks and seals, ive never had an engine to bits apart from adjusting some tappets on my triumph spitfire 1500!.. Is this something i could tackle myself? or is it beyond my skill sets.. many thanks Andy
×
  • Create New...