It sounds like you're taking a methodical approach to troubleshooting the issues with your bike, starting with addressing the visible damage to the plastics and the rear tire. Ordering a new throttle cable is a good call, as a stiff and stuck cable could definitely cause starting problems.
Given the extent of the damage and the complexity of motorcycle electronics, it might be beneficial to seek professional help from experts like www.alldryus.com. They specialize in water damage restoration and could assess the bike thoroughly to identify any hidden issues and provide guidance on the best course of action for repair.
Thanks for that bud, it is all good now.
Not heard of a company like that before, but will bookmark that for future reference.
sounds like you're taking a methodical approach to troubleshooting the issues with your bike, starting with addressing the visible damage to the plastics and the rear tire
ordering a new throttle cable is a good call, as a stiff and stuck cable could definitely cause starting problems.
Throttle cable replacement is best with the throttle body off the bike. Since you have a lot of the bike apart, you’re nearly there. Remove the silencer mounting bolt from the air box and the 2x 10mm nuts and 10mm bolt the air box will be almost free. The petrol tank will need lifting too.
There is a lot of rubber pipe work running from the cylinder head breather to the air box, all this can be removed. Just blank the hole in the air box and use some of the grey pipe to make a new head breather that runs down the side of the radiator on to the sump guard. A little weight saved and much neater under the petrol tank.
Make a note of where the lock nut is on the cable, undo the cable from the throttle body by turning the body. Fit the new cable to the body and tighten the lock nut in the same position as the old one.
It takes a little patience in getting the new cable routed under the tank so it does not pull the cable when the steering is turned, particularly to the right
Thanks for that info bud, really helpful.
I didn’t get time to do any work on it at the weekend, might try later today.
My new parts arrived yesterday, so I will make a start on fitting them today.
I still think the hardest part to install will be the throttle cable.
I have still not managed to remove the old damaged one, as it looks like I will either have to twist or remove the whole of the EFI throttle body to remove and refit the new cable,
Any tips on removing and replacing the throttle cable guys?
Sadly we has a fire at our house last week and my Montesa 4RT suffered some fire, smoke and water damage.
It’s not insured regrettably so I have to see if I can get it up and running again.
The heat and fire damage seems to have affected a few plastics like the rear mudguard and also killed the rear tyre too.
However at this point I also can’t get it to start at all, so I’ve been trying to work out what’s wrong in a step by step fault finding basis.
The first thing we noticed was that the throttle cable was stiff and stuck and not returning to its home position.
We have now removed that and will order a new one.
The bike is still not starting though, so we pulled the plug out and it’s not sparking at all on kick over.
We did notice that the jitsie magnetic kill pull looked like the cables might have melted., so tried unplugging that and shorting the ignition feed.
Still no spark.
So what’s the best next steps to fault find why we don’t have a spark.
Thanks for any tips or pointers!
Update and thanks for the response to others too.
It was indeed the melted cables on the jitsie magnetic cut out, it looked like one of them was shorting to the handlebar hence making the ignition cut out.
Disconnected it and removed it completely and when we put the plug back in it fired up straight away.
We will get the cable ordered now and start on the rest of the mostly cosmetic damage to get it back to normal.
Thanks again.
So I’ve ordered a new rear tyre, a rear mudguard, a new kill switch and a new throttle cable, they should be delivered Friday, so I can fit most bits at the weekend.
I will post some pictures of rhe work as I do each section.
Does the tip over sensor appear damaged? It's located back there close to the rear fender and tire, plus it can definitely stop the engine from running.
The bank angle thingy? Nope that was one of the first things I looked at, and it seems fine.
Anyway as posted it was indeed the kill switch , and it’s running again now!
Sadly we has a fire at our house last week and my Montesa 4RT suffered some fire, smoke and water damage.
It’s not insured regrettably so I have to see if I can get it up and running again.
The heat and fire damage seems to have affected a few plastics like the rear mudguard and also killed the rear tyre too.
However at this point I also can’t get it to start at all, so I’ve been trying to work out what’s wrong in a step by step fault finding basis.
The first thing we noticed was that the throttle cable was stiff and stuck and not returning to its home position.
We have now removed that and will order a new one.
The bike is still not starting though, so we pulled the plug out and it’s not sparking at all on kick over.
We did notice that the jitsie magnetic kill pull looked like the cables might have melted., so tried unplugging that and shorting the ignition feed.
Still no spark.
So what’s the best next steps to fault find why we don’t have a spark.
Thanks for any tips or pointers!
Update and thanks for the response to others too.
It was indeed the melted cables on the jitsie magnetic cut out, it looked like one of them was shorting to the handlebar hence making the ignition cut out.
Disconnected it and removed it completely and when we put the plug back in it fired up straight away.
We will get the cable ordered now and start on the rest of the mostly cosmetic damage to get it back to normal.
Honda Electric
in Honda
Posted
Yep I think that ship has sailed when they announced the end of that partnership!