Jump to content

What Did You Do To Your Bultaco Today?


scot taco
 Share

Recommended Posts

 

 

It is quite an adventure to open a tank , and it also takes a certain amount of nerve,  also kind of scary. 

I have done so on more occasions than I wanted to, but such is life with old machinery.

By the way the chain guard looks really good, I have always wimped out & paid for the SM, good work.

Mod 49 tank

 

putting back can be a bother!!

post-14329-0-72440600-1435174063_thumb.jpg

Naturally this was a painted tank that I messed  up the first go around

All good now

Hope this helps

Larry

Edited by lbhbul
  • Like 3
Link to comment
Share on other sites

 

 I had thought of cutting the two big slots like you did but the boat repair man reckoned it wouldn't make any difference just cutting the thing in two bits. 

Yours turned out looking really good Larry. Did you use anything inside it again afterwards. Brian was telling me he has a resin that he uses in chemical tanks that's resistant to acids, but ethanol's not really an acid, so I might go with whatever is currently the best - caswell maybe

Link to comment
Share on other sites

 

Yes I did use a product that is available here but maybe not where you are, I have a friend who

uses Caswell, to good end.

The whole thing depends on how clean you get the tank prior to lining that makes the job good or not.

I do not use any Ethanol, however modern fuel, and polyester resin, NOT GOOD!!!

 

But back to my Blue girl---

 On the way to turn on the air 9:00 am (east; right in the sun)

post-14329-0-60597400-1435185986_thumb.jpg

Little later in cool shop

post-14329-0-16543000-1435186182_thumb.jpg

More later as I'm old and slow

Larry

PS That head steady don't look right??

 

  • Like 2
Link to comment
Share on other sites

 

Well maybe not much going on out there??

Made a little progress since last time, not a whole lot for most, but for me

enough sitting on rolling seat to do me, and also stopped to help out a

friend and do some machine work yesterday

.

Add a condenser

post-14329-0-51059700-1435413707_thumb.jpg

 

Up  on the lift for a little clutch work

 

post-14329-0-84123500-1435413857_thumb.jpg

 

Now we can get it to where its easier to work on.

Larry

  • Like 5
Link to comment
Share on other sites

 

Thanks for the comments on the Pursang.I bought it in 1998 for 300.00,went through it and have been racing it ever since as family and work permits.It has been extremely reliable and the handling has saved me more than once!

 

Tailie, you do very nice work- looks good.

 

Larry,glad to see that you have a good project to have a reason to be out in the shop.Not a bad looking bike and I,m sure it will be running like a top when it leaves OK Bultaco.

 

I have off this coming Friday so I,m going to take the Sherpa T out to the nearest riding area,about an hour and fifteen away,and get some practise in.

 

Everyone take care and keep the rubber side down :thumbup:

  • Like 3
Link to comment
Share on other sites

 

Put a set of Betor rear shocks on my sweet Model 92.  Feels better, but I still need a new set of tires for things to be perfect.  LOVE how easy this starts up and runs.  Just toying with the idea of a smaller front or larger rear sprocket to slow it down just a bit.  But it sure loves to pull uphill!  And once I find a muffler my neighbors will be happy too!

post-20184-0-60481800-1435432822_thumb.jpg

post-20184-0-82745200-1435432938_thumb.jpg

  • Like 7
Link to comment
Share on other sites

 

Yesterday trying to get myself going after several hours Friday helping my good friend to sort out

the kicker on a MAR & chain tensioner/brake cross shaft repair, back on the 199a project.

 

Not much but safety wire clutch and refit case, 300cc Dexron , change tank bolt configuration.

 

stock tank bolt

 

post-14329-0-27758700-1435499313_thumb.jpg

 

maybe cleaner

 

post-14329-0-12730000-1435499446_thumb.jpg

 

 

 

 

  • Like 4
Link to comment
Share on other sites

 
 

What did I do to my Bultaco today?

I tried very hard to break it at the acquaduct classics trial. Great trial but expert route bit beyond my modest talents - very slippy rocks

Bike survived a few falls but puncture 2 sections before the end stopped play...

  • Like 3
Link to comment
Share on other sites

 

I rode a two day trial in North Queensland over the weekend so today I washed my bike and then cleaned the brakes out and regreased the brake cams in each wheel and rotated the rear tyre to straighten the valve ready for our club day this Sunday. Ready to go again.

  • Like 4
Link to comment
Share on other sites

 

Well guys the saga of the Blue Bultaco continues, on to fork seals, started out OK but then became

complicated; sticky/stuck rather badly

post-14329-0-45397500-1436215375_thumb.jpg

its the RH

post-14329-0-22218100-1436215590_thumb.jpg

here we go

post-14329-0-40703200-1436215689_thumb.jpg

got to fix this or junk it

post-14329-0-63681600-1436215795_thumb.jpg

all better now

post-14329-0-56441400-1436215890_thumb.jpg

I'll finish up the rest of the story later.

Larry

 

 

 

 

 

  • Like 1
Link to comment
Share on other sites

 

I think i have a 199A ! it looks like one. It say 199A on the frame and on the right hand engine case but the gear box 

drain pug is in the wrong place ! same place as a 199 so it looks like one of the cases is from a 199 ?  it has 199 printed on it looks like it was cast into it.  Top of barrel also has   l  ( then a three legged symbol then ) 199-1 im just wondering how much of the engine is 199 and how much is 199A It runs really well other riders tell me so, im just happy it works. 

 

I have been trying to load photo but can not get them to up load even tried advanced up loader will have an other go after tee.

 

Thanks for any feed back  BR 

  • Like 1
Link to comment
Share on other sites

 

The main difference between 199, and 199a I believe is , the 199a has 3 main bearings, 199 has 2.

The LH case with bottom drain is common to earlier m159 and forward  and the problem would only

be clearance on the skid plate used on 199a bikes.

There would be no mechanical problem encountered with the earlier LH case.

Hope this helps

Larry

 

 

  • Like 1
Link to comment
Share on other sites

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
  • Create New...