I have recently purchased a 2018 TRS one 300. It has a front LED, map switch and another switch all located in behind the front panel between the forks. I thought this was extras that the bike did not have however after spotting some extra wiring I’m not so sure… it’s appears someone has been cutting wires in the past.
Is there benefits to the map switch? And what would the cut wires do?
I have 3 plugs And from info online I can see that the Orange/grey is for the map switch. Green/yellow is switch for LED lamps and Green/black is ?? And if I have the wiring for the LED switch am I just not finding the wiring for the LED light?
I changed the stator in a 2009 Sherco 250. I have found the mark on the flywheel but not on the engine casing. I am using the timing guide here: http://www.lewisportusa.com/manuals/sherc_11-21-09/sherco_ignition_timing_supplement_03-04.pdfthe old stator had 7 coils and the new one has 4 coils. (Including the pick up point) the pick up point is also bigger on the new one if that affects anything.
My bike has stopped starting so I checked fuel, carburettor, spark plug and so on. I have read up about it and it sounds as if it could be the stator or the starting coil. How would I check to see if they are faulty without replacing them?
I was driving through a loch with my friend, I drove into a deep bit and the air box took some water in. I reached the other side and the bike died. When I kicked it, it started but it was struggling and if was given too much revs died. When I emptied the air box there was a lot of water. I have cleaned the carb and dried the spark plug as well (as it was wet). It will still not start does anyone have any ideas what is stopping it?
I bought a sherco side stand from splatshop and after a few rides my friends pointed out that it is creating a wear mark on my tyre. I was just wandering if there is any thing i could do about it? Thanks.
Hi I had this problem as well for ordering a kick stand. To find the year you need to have the frame no. (located on the right hand side of your steering column) the 10th number is the year built. (For me it's 7, I have an 08 though.) For the cc you need the engine no. The engine number is located in front of your back suspension on the left hand side. There will be two letters before it then the cc. For me it's 250. Hope this helps :-)
I had a look around and i found a complete side stand for a sherco. The only problem is that it says I need three 20mm and one 12mm but i have only got 3 tapped holes. Here is the link to the side stand. www.splatshop.co.uk/sherco-side-stand-complete.html
I have had my Sherco for a few weeks now and it hasn't got a stand. so I was wandering if anyone knew which number I use the frame or the engine no. to get a stand?
2018 TRS Wiring
in TRS
Posted
I have recently purchased a 2018 TRS one 300. It has a front LED, map switch and another switch all located in behind the front panel between the forks. I thought this was extras that the bike did not have however after spotting some extra wiring I’m not so sure… it’s appears someone has been cutting wires in the past.
Is there benefits to the map switch? And what would the cut wires do?
I have 3 plugs And from info online I can see that the Orange/grey is for the map switch. Green/yellow is switch for LED lamps and Green/black is ?? And if I have the wiring for the LED switch am I just not finding the wiring for the LED light?
https://trsmotorcycles.com/archivos/adjuntos/ManualDespieceTRRSRagaRacing-250-280-300-2018.pdf Page 26/27
https://drive.google.com/file/d/1CfgC0HcEFnCTDmIOaTPFu84BI8-D8LiD/view Page 19
Any help much appreciated