spike2450

Hi I want to replace the fork oil on a 2006 250 pro, ( black forks / presumably ally ), is there a definative start to finish guide, i have searched on this forum and there seems to be different views especially on the amount of oil etc. Any help / opinions are appreciated.

Hi Best to do a search on bleeding rear brakes, they can be a pain to bleed but there's plenty of ideas on this forum that will help. Good luck.

hi have a trial in the morning and couldnt get any Castrol tts that i normally run at 75/1, all i could get was valvoline fully synthetic competion oil, anyone else use this oil and to what mix ratio, any help will be great!! regards

Hi Has anyone got any ideal ( initial ) settings for the front forks. There appears to be quite a few different views on the quantity of gearbox oil to use. I've always used dexron3 and am initially going to use 450mils, any help would be great. Had one ride on the 250 Pro and i'm very happy with her!! if only she was blonde!!!!

Hi Thanks for the reply, i removed the shock and it was easy to turn when it was of the bike, so i have set it to 18 clicks out and set the spring to 120mm length as suggested on this forum. thanks again

Hi all Just traded in and have now a 2006 250pro, checking her over as you do!! and on my rear shock adjustment (Gold Ohlin) she appeared to be fully wound in, but then she only unwound / came out approx 10 clicks before unwinding easily with no clicks. Have i got a problem? I've read the related forum and the average i think was 40 clicks total range and to set it 18 to 20 clicks out!! When the adjuster is wound fully in how much of a gap should there be between the top of the black knob adjuster and the bottom of the spring cup (hard to explain), is it possible that it's full of crap and wasn't wound in fully? i've tried forcing it i.e. winding it in and am only getting about 10 clicks back out before again turning freely. The rear does seem to be responding i.e softer / harder. Sorry for the long winded plea for help, but i need to know if i should take her back to the dealer. regards dave

Hi all I had a trial today and i'm having problems with my front brakes always spongy even when well bled (well practiced), i was wondering if the problem is with my front brake master cylinder/resevoir is there a repair kit or method of cleaning the resevoir. thanks in advance.

Hi all Purchased new sprockets and an o-ring chain, my original front sprocket was 10 teeth and the shop has supplied me with 11 teeth, what difference will it make to the bike, or should i take it back and get the same size 10 teeth, any help would be great.

thanks for the reply, does the rear brake pedal need to be wired open or can you leave it as it is?

hi all I took calipers apart to clean and then bleed, front all done ok, but the rear has been a bitch to bleed and i've just noticed that there's air/oil leeking from around one of the pistons, are there any good tips for replacing seals / bleeding the rear? Do i have to replace the seal? any tricks around it as i am pushed for time as i have my first trial in two days. And do you get new pistons in a repair kit? Thanks in advance.

hi all i have a 2002 txt 280 standard for about 3 weeks. Still catching up on maintenance needed, and have attacked the rear suspension tonight and have found and not to my suprise everything dry as a bone!!! I've found an adjustment setting on the bottom of the shock that had been facing the engine and i didn't know it was there until i spun it around!! and i presume that it should face to the rear for adjustment? is this the rebound? My problem is the gold annodized rocker arms!! when i've spun the shock around they have reversed from the original position i.e dog bone to swing arm connectors, does this matter? or is there only one way to install them? Sorry for the book like question!! Thanks for everones help so far, this forum is a big help and appreciated.

250 size and up montesa from 2004 on, cheers

hi been impressed with a 2002 txt 280 standard, and i'm thinking of trading it in for a newer model, do i go for a gas gas pro or is a montesa a better machine. Obviously the wrong forum to ask the question!! but some honest views would be great.

I have moved this post from a previous one due to a different problem. Checked my bike tonight and the 280 2002 txt standard is fine going up the gears but coming back down hits a false neutral between 6th and 5th gear, not really a problem for me, but what are the possible causes and could it escalate to further problems ? Are there other known problems with this bike that i need to look for? I am so far very happy and impressed with it

Checked my bike tonight and the 280 2002 txt standard is fine going up the gears but coming back down hits a false neutral between 6th and 5th gear, not really a problem for me, but what are the possible causes and could it escalate to further problems ? Are there other known problems with this bike that i need to look for? I am so far very happy and impressed with it.