Jump to content

scorpa01

Members
  • Posts

    25
  • Joined

  • Last visited

Everything posted by scorpa01
 
 
  1. just wanna check some thing with you fan kicks in but when i rev the bike or start moving again it cuts out and stops but as soon as i release the revs or stop the bike it kicks in again is this normal its a 2001 sy250. also did a trial at weekend and it was on the hills had to go up a long steep hill to get to the next section and bike started to overheat and produce steam from top of the rad. please dont think its to do with the fan as its been like this since i bought the bike but the overheating has only just occured and had the bike about 10 month so any help welcomed cheers james
  2. scorpa01

    Sherco 320 4T

    yeah its a fantastic bike when running cannot fault it just so hard to get going again , but still open to suggestions off anyone all welcome cheers
  3. i've done this job on my 2001 as smokes heavy but is still the same as before so not gauranteed fix
  4. scorpa01

    Sherco 320 4T

    could do with a little help not for me for a friend as i have the uber reliable scorpa 250 , any way he has bought one off the above 4T ON A 05 it has the kehien carb and the decompression lever and the exhaust heat guard near the carb but this is still proving to be a utter t**t to start hot or cold , have read a few post on them but no one seems to give a good clear answer on how to solve the problem of the starting issue. please could anyone put pics or even replys up for everyone to see even vids of your own running cheers .
  5. hi there thanks very much for the detailed reply it was smokey when i bought it but not as bad as it is now to be honest ,i never thought about the exhaust being full of crap , but how would you clean it as it is a sealed unit ???, it does seem to use oil thats wot makes me think it is the oil seal it uses about 75/100ml after about 4 rides for about 4/5 hrs each ride . i'm gonna try and get a video of it running and post it up . Its not that bad on tick over but when reved plumes of smoke. ;(
  6. do you really need to split the casing to do this job ??????
  7. just wondering weather anyone has changed there crankshaft oil seal , would like to know where it is , how hard to do it , and would this stop it from being like a smog when riding it i've already tryed to do a number of things to eliminate this by playing with the air / fuel mixture , the amount of 2 stroke oil i put in but still smoking like mad. if anyone could upload pics this would be great cheers james
  8. cheers will give that a try once put it all back together again pal but av got to do the crankshaft oil seal as well as mine is very very smokey ,just wondering if any one has do this job on there scorpa and how hard it is and where abouts is it ?????
  9. managed to bleed it up now the plunger had got stuck in the master cylinder probably due to lack of use for 3/4 month not the best weather though has it , but the problem is that even when the clutch is engaged it still moving do the clutch plates want removing and cleaning ???????????
  10. cheers for that i will give it a go and see if it work will let you know
  11. hi there wanted to change clutch oil on my scorpa sy250 2001 and wanted to know how to bleed the new oil back through as i have been trying to do it like i would doin the brakes but carnt seem to get any build up of pressure at all , been pumping clutch lever to force the oil through but still nothing help need please.
  12. think I've found the problem when I started it up I pulled the clutch in and selected a gear then let it out but nothing happened so pulled clutch leaver back in and out then it released and started going , but some times when I pull the clutch in it sometimes sticks and will not pull back to the handle bars feels like the spring inside the master cylinder is sticking so probably have to get a master cylinder kit to sort it out , its just strange how its gone like that all of a sudden.
  13. i could'nt select the gears as it would either jump off and go with the clutch in or would stall as soon as you put it into gear. really strange as it was fine 2 week ago cause that was the last time i used it an just put it back in the shed. i have cleaned the carb and changed the gear oil that should'nt have done anything to it.
  14. came to my scorpa today started it up no problem pulled clutch in selected 1 and cluch did't work , yet it was working only 2 week ago when i was out on it , theres no leak and resavour is still full has anyone got any ideas please surpose to be doin a trial tomorrow cheers .
  15. thanks for the ideas people but the alli blocks are about 15/20mm thick so cannot even tap them , i've just got a dremmal se what a can do with that lol loads of different bits in there to play with.
  16. hi there my scorpa is a 01 on the swing arm it has 2x aluminium blocks with groves on it so you can move the rear wheel on the snail cams , the snail cams go up against theses but mine are getting worn now and there's not much you can do with them just wanted to know has anyone made a modification to theses , has anyone else got the same prob or even seen this prob before. ALL HELP CONSIDERED AND WONT BE WASTED!!!!!!!
  17. at the moment its 60:1 just cause of the top end rebuild
  18. scorpa01

    scorpa smoking

    hi there i have a 2001 scorpa i noticed that it is quite smokey when riding , i have recently changed the piston , rings , bearing and gasket so i have alittle more 2 stroke oil in at the moment , but i have noticed that gas gas dont produce hardly any smoke at all any help will be great on how to reduce this smog when riding cheers james
  19. Yeah a will be hopefully want to start taking it a little more serious now , need to get my fitness up though am knackered after a couple of attempted sections lol , think al have to get a mountain bike as well now the expense just keeps coming lol , but i surpose its cheaper than motorcross at the end of the day. also where and when is the next trial do you know ??
  20. hi thanks for the details of what i had to do but i did'nt end up doing the trial as there was no beginner route at this trial as my mate forgot to tell me but the next one that rochdale / darwen trial i will be doing it so hopefully i will see you there next time , i believe it was quite a hard trial up there on sunday not sure where he came will have a check an let you know cheers once again james
  21. could you tell me some info on what to do and what to expect when i get to the venue its at LEE QUARRY , BACUP tomorrow i am doing it with my mate but he's an intermediate and i'm a beginner so he will be doing different section , any help will be great cheers james
  22. i know its a scorpa and i understand they are loud when running but my friend has told me to change them as its a sort of chattering noise and dont want it to start scoreing the barrel other wise expensive job that could be saved by replacing the rings and piston if needs be p.s also what sort of money am i looking at to change everything
  23. hi there just wondering weather you could help me ,i need to change the piston and rings in my 00/01 scorpa 250 , i just wanted to know do i really need to change the piston itself could i get away with just cleaning the piston up and just changing the rings and small bearing ,i would like to do the lot but funds are against me do you think it is good or bad idea please give me your thoughts all helps cheers james
  24. hi there thanks for the replies the sprocket has 6 holes to fit it to the hub i've tryed to striaghten it up on the spokes its made it rideable but really need sorting out the spokes look ok but the rim itself is bent so anyone who nows anywhere in the north west could you let us know cheers james
  25. hi there only just registered to this site in the last 5 mins , i need some help please i have a scorpa 2000 / 2001 an my rear wheel is buckled i am trying to find a second had rear wheel but these are rare as rocking horse s''t what other wheel could i use i have found a gasgas jtx rear wheel would this be suitable if anyone knows absolutly anything to help me please post something or even if someone could give me a way of striagtening it i will try anything to save a few
 
×
  • Create New...