[4rt Factory Front Brake]

All done and what a difference, feels much more positive. As for the source just lucky on eBay. However it's a CR 80,125,250 CRF 250 etc

[4rt Factory Front Brake]

Am just fitting one now, I've bought a new one off eBay for £27, just need to find somewhere I can get the banjo bolt from.

[is there any sherco trials pants/top ?]

Try section5 trials in google, they have the lot.

Infact here you go

sherco

[60 Plate Kangoo]

got 2 bikes in kangoo. One in forward one backwards diagonally. Easily and a good fit

is that a 60 plate one??

[Fender and Decals]

Try ebay for the decals, but you get what you paid for.

[a word of warning]

[60 Plate Kangoo]

I don't know how it compares size wise but two trials bikes would fit on the old Kangoo van.

How ??? you got any pictures

[brakes again!]

Thanks cope that's a good tip

[help ! main bearing - sherco 250 (03)]

Here's a start for you

http://www.sherco.com/wayne/Sherco_Engine_Teardown_and_Assembly_Manual.pdf

[brakes again!]

Ok, things are getting a bit clearer now .... But please tell me where you got all that for just 7 quid from?

Best of balance.

Neo

I have a very good friend who doesnt mind giving me discount

[brakes again!]

repair kit , MC, springs, boot and clip

[brakes again!]

Well that's what am putting it down to, most of the time if you look the boot isn't really giving a seal!

Only other thing I can think of is when I back bleeded it, this has pushed the seals out ??? But for 7 quid am not going to complain

[brakes again!]

On a 2010 bike

Yep, thing is all the dirt and mud can easy get inside, its only a rubber boot that stops it

[brakes again!]

haha fair enough,

New master cylinder!!!!

nice and easy fix

[brakes again!]

all sorted !!!

[wheel rim stickers]

[brakes again!]

I just do not understand this Isuppose. Why would you want to bleed the brakes while replacing pads? And on a '10 model?

I always change my brake fluid when I replace my pads cope!! Abit geeky I know but thats my maintance

After a bit of messing about I think its the master cylinder because there's no pressure there

[brakes again!]

Cool that will do

[brakes again!]

Ok was replacing my front pads and everything was going well, then start to bleed the system and the pistons wont move!!!

No matter which way I try it they wont come out, so tried to split the case and low and behold the head of the bolt is chewed to bits

Anyone got any ideas on how to free them,I was think compressed air but wont this damage the seals???

as always thanks guys

[TY80 Trial in North East?]

Richmond club run a few ty80 trials try them

http://www.richmondmotorclub.com/about/

[TY80 Trial in North East?]

Hi,

Does anyone know when the next TY80 trial will be on in the North East Area

Cheers

where about are you, the north east is a big place

[Grip !]

Seems the other bikes were on a Mich! Not sure what type sections you're running, but I think in a rockey burn section the Mich r Dunlop may prevail for grip on the rocks, even if the mudboys like the IRC.

Am running a michie x light on the rear and the grip is unreal

[Grip !]

hmmm my 10 has loads of grip, I would put it down to the tyres myself

[escort van]

Does anybody know if a full size trials bike will fit??

[decals and plastics]

On a 03 you can use upto a 05 rear mudguard and stickers(as the tanks the same)

There was a thread about someone making a 07 mudguard fit but is it really worth the hassle??