|
-
-
Hello! Does someone know which is the torque Nm for the upper and lower triple clamp on a Gasgas txt 125gp 2019? Thanks, Stathis
-
Thank you Peterh , nice bike , be nice till 200 hours !
-
Nice job !
Could you post a picture of all the bike ?
-
Also , ATF Dexron III , 400 cc . Drain the oil after you have hot the engine .
-
Hi Peterh , after changing all the bearings , I did the same you have done and now its ok , everything is moving free .
I did the same with the chain tensioner , to have more room there , so I can adjust correctly the rear wheel .
-
Hello Peterh , did you solved the problem ?
Mine has started the same . I believe that its the bearings , I will see them tomorrow . What did you do , changed the shock ?
-
Its a raining day , so the picture is not very clear , but I hope it will help you . I am 95 Kg ( without breakfast ... ) so I needed to preload the spring to set the sag . Where exactly is your problem ?
-
Hi Peterh I have a 2014 with elka suspension from the 2015 . There is no problem . Could you take a picture ?
-
Hello , i dont really know about competinions license , i know about Aspergers syndrome ( speech and language pathologist and therapist ) .
If you have a road licence , i cant think why cant you joint a competition .
I think that it would be better for you to go to a trials school first or find some people to ride with them , before you go to a competition .
Good luck , Stathis
-
Thanks for all that information Peterh !
i also have a coffee coloured spark plug , but i am not fully contented .
The previous owner made some changes to the carb . I have to find them and fix it ( pulled out the main get , says 105 and i messured it and its 140 ! , so i changed it with a 120 ) .)
I wiil try buy the Boyesen Reeds and try the Chapion plug .
I also like to clean the air filter after every ride .
I love the bike too . My bigger problem is that i broke my toe and now i have to wait 3 weeks before i can ride again .
So now its an opportunity to set the bike !
Sorry for my bad english .....
-
Thank you gasgas249uk . Any other information for jetting is welcome .
Why 70/1 ? The manual gives 100/1 .
-
Hello from Greece . Just bought a jotagas 300 , 2014 .
I would like to ask a standar jetting for the dellorto 26 carb ( main jet , pilot jet , needle .... ) , so i can adjust it .
It is not absolutely clear in low raves .
Thanks a lot , Stathis .
-
The backplate on the clutch is not bent or warped . Thats my realy problem , everything looks ok , and my engineer say that the problem is the quality of the gears .
Thanks again for all the answers , its the only help i have .
-
Thank you copemech . The bearing is ok , no movement . I think , i have to open the cases .
-
The transmission main shaft is not moving at all . The other shaft where the idle gear places is moving very litle .
Thanks for the answers .
-
To make it easier to kick start - do not kick back .
-
Thank you .
Yes , it make a buzzing noise while running ( i think thats the noise of the worn gears ) .
Where is that metal tab zippy ?
-
Photo of the gears . The small clutch primary drive gear have twisted teeths and the idle gear is worn .
No broken piece anyware .
-
HelIo from GREECE . I would like to tell me your opinion on a problem that I face.
In June 2013, I changed the clutch primary drive gear , the kickstart idle gear , the kickstart pinion and all the bearings , because they had bent their teeth.
After five months with very little use in the backyard, heard a noise again. Opening the clutch, and we see that the teeth of the 3 gears are warped again. Should note that I have returded the ignition, get ahead with the first kick and change the oil enery 10 hours .
I really don't know what to do . Get new gears for 5 months use again ? Is there an other problem I cant understand ?
Thank you and really sorry for my English , Stathis.
-
Thanks copemech . I thing i found it in splatshop blogs , talking about sherco forks from 06 - 11 .
-
Thank you KOZZR . I suppose there are no differents between Ceriani and Pioli forks .
-
Hello from Greece . I cant find in the forum , how much oil needs each fork leg . My bike is a sherco 250 2009 and it has ceriani forks . Thank you .
-
Hi j0rdi , i like your English and wait for pictures .
-
Hello nikosthegar. Xalkida . You ?
|
|