[Tissue in exhaust]

The packing you have removed acts as a silencer, so you need to repack with new packing. Before re-packing, blow a heat gun through the exhaust for a few minutes, it will heat up and burn off the oil.

 

[Monoshock special]

Mr Gollner got the measurements right!

Spoiler

 

 

[Closed to club]

If this second spike carries on, none of us will be out there!

[Seeley photos]

I still use mine regularly, although it has grown up into a 250.

[slow action throttle]

You do notice a difference.

[april 13/14 Caglio first round Italy]

Quite a few of us coming over to ride at the weekend. Looking forward to it!

[BETA 4T THROTTLE CABLE]

Do you have the Beta twist grip or Domino? I had problems when I fitted a slow action to mine.

[Hello from North Lincs]

How did you get on Steve? You looked to be doing ok from what I saw. Didn't get a chance to say hello but hope to see you at the next one as well!

[Hello from North Lincs]

Welcome Steve, nice easy Scunthorpe club trial at Whitton on Sunday! Jump in at the deep end, go on you know you want to.

 

[Mont 200 wheel spacers]

Just measured mine, 15mm.

[Mont 200 wheel spacers]

Two different types of front wheels in the 200's. I will measure mine tomorrow. Can you slide the spindle and wheel sideways in the fork clamps to centre it?

[Cota 223]

Has anyone tried the 223cc mod on a Cota 200?

Fit a 247 piston in a 200 barrel = 223cc.

[Beta Evo 4t 300 first ride experience]

On 19/09/2018 at 8:04 PM, mrturtle said:

Have you not ridden the 300 2t then? ?

Don't do 2t, I like the engine braking of the 4t.

[Beta Evo 4t 300 first ride experience]

I have a 2016 and it is the best bike I have ever ridden!

[Evo 4t Carb]

My poor running same as yours was fixed with half a turn on the fuel screw. Anti clock to ritchen.

[IRC tyre on a 2016 Evo 4t.]

I have a IRC tubeless on my 16 Evo 4t and it is great. No problems at all and much better than the Michelin it had on before!

[The Cush drive]

The 250 has the rear sprocket bolted directly to the hub!

Seems to work ok.

[Beta Evo 4t Air Screw ????]

Turned the mixture screw out half a turn.

[Beta Evo 4t Air Screw ????]

Well at least you will have no trouble adjusting the pilot mixture in future. I made a tool to do this as mine suffered from the dreaded backfire on over run, now spot on.

[Beta Evo 4t Air Screw ????]

I think you will find it is a fuel screw not air. What is the problem? How did it run before?

[Evo 4T waterproofing.]

Just got a 2016 300 4t. The wiring to the CDI and regulator look a bit exposed, should the connectors be protected / sealed etc.

[Evo suspension settings]

Can anyone tell me how much 'Static sag' (bike weight only) I should have front and rear. Evo 300 2016.

[Betor shocks which way up?]

Easy to check, remove one of the shocks, remove the spring and test for damping each way up.

Some work both ways and some models don't.

[Tyre Wear.]

Its all in your head. If you think your bike has good grip then you don't need new tyres.

I turn and replace regularly, because I think I need to.

Having the correct pressures is far more important!

[Seeley Vs Xl185]

Can anyone confirm that the original engine in a Seeley is based on the XL185?

If so do most parts fit, clutch, bearings, seals etc.