jes42

HI, I fitted one and managed to bleed the brake to ALMOST as it should be but was struggling to get lever pressure. After asking around someone told me to remove the master cyl cap and just"flick" the brake lever enough to move the piston about 2-3mm and watch for little bubbles, sure enough the last bit of air came out and now have pressure at the lever and the brake is perfect except for a bit squeaky from fluid on the pads. The only downside is it took a good half hour or more of fiddling with the lever but it's worth knowing. Good luck with yours.

Thanks for that mate, excuse my ignorance but does this mean you bleed using the banjo bolt and don't touch the grub screw? What's the difference between the two banjo bolts? Cheers again.

Have just fitted an xblok front caliper to my evo. Can anyone give an explanation of the best way to bleed the system ? There is no bleed nipple fitted, just a small grub screw, is this normal or should there be a proper nipple ? Many Thanks.

Does anyone know if the evo heavy duty springs from SXS will fit onto a ohlins shock ?

Thanks for that, I,ll check 'em out.

Good point!!!!!!! 2011 evo 290. Might help!!! Cheers

Does anyone have any ref nos for the swinging arm and suspension linkage roller bearings ? Cheers...

X11's looking favourite so far. I think I'd still go for IRC if seller agreed to swap it if it's not right though.

Am ready for a ner back tyre for my evo, are there still problems with th IRC's not staying up on the MORAD/DID rims? Also how do x Lites compare for grip?

Hi Mate. I had the same thing with my '04, it might sound obvious but have you made sure you're not kinking the fuel pipe when putting the tank back on ? Mine had been shortened a time or two over the years and so couldn't be routed properly, a longer pipe sorted it. I know it's basic but I fell for it!!!!! Good luck.

Definitely interested and thanks. Just let me know how much I owe you and how to pay. Just I/m'd you on here but it wouldn't send. Try messaging me and we can sort it from there. Thanks again.

Saw something the other day about "down and back peg hangers". Does anyone know if these are available and if so where to get any? I'm doing some tinkering with my 315 and wouldn't mind trying a set.

Has anyone had trouble with IRC tyres not staying up? A mates had one on his new beta from new and it just wont stay up. They are superbly "grippy" tyres especially in muddy conditions but are they let down by this ? I've had one and it was the same on my rev3 with rim tape but this ones just as bad on the new rim i.e. Morad or DID....

Looks like you got it spot on with the icing mate!!! Went out today without altering anything, bike ran sweet as a nut. I'll remember that one in future. Cheers.

To richen it up do I screw it out further on this carb? Also, now you mention it, it was really cold last time out so the carb could have been iced up. Am out tomorrow so will have a play with the mixture screw and see what happens. Thanks for the help.

Dellorto, air screw to the left of tickover screw. I've got that 4 turns out. Thanks.

Can anyone tell me what jetting I should have in my '04 315? I've stripped and cleaned the carb and the bikes running ok but seems a little "weak" off the bottom end? Cant see any wear or damage to needle or slide but I can change 'em if needed. Not sure what jets are in at present. Any and all advice on carb set up will be greatly received!!! Cheers guys.

Hi.. Will a 4rt rear mudguard fit straight on to a 04 315? Cheers.

Thanks for that.

Another quick question re the 315r... Whilst stripping and cleaning the carb I noticed a split in one of the pipes. It's the one that forms a kind of loop from one side of the carb to the other, it looks like it may be 1 pipe for 2 breathers instead of 2 seperate pipes. I've never stripped one of these before so please excuse my ignorance!!!! Should it be split or not????? Again, all/any advice welcome!!! Thanks

Thanks guys. Used a combination of all the advice - bunged up the end and soaked overnight in paraffin, then after letting it dry out blew it through with compressed air, loads of crap came out so it must be an improvement. The clutch plates are the apico ones which are slightly cross-hatched to allow a bit of oil to stick and hopefully cure the drag. Not tried it yet but will post on here with the results. Out for a practise on Wednesday so fingers crossed!!!

Just bought a 2004 315r and want to tidy it up and give it a once over. Have fitted some new clutch plates to hopefully sort out a bit of clutch drag and all the usual stuff, oil change, filter, plug etc but I want to repack the silencer and decoke the mid box as it looks a bit gungy!! Whats the best/easiest way of doing it ? Any help greatly appreciated. Also, does anyone know where I might get a "Lampkin Replica" graphics set from? Cheers.

Not tried any yet mate so cant help - sorry! Hopefully you can let me know what they're like.

You mean you raised the bars by 40mm? Sounds a lot but if it works.... What year is your scorpa? I have an 09 and am looking to raise the bars but so far I can only find the S3 risers and think they are a bit pricey, also paying for fore/aft adjustment which I'm not sure is necessary....Any thoughts or advice more than helpful...Thanks

What type of risers are you using ? 40 mm sounds a lot. I'm looking for some for my scorpa and believe I need the same as the ones for the gas gas. Any ideas ? Cheers.