Jump to content

What Size Hex Key?


tombo46
 Share

Recommended Posts

 

 
Does anyone know what siz Hex key is needed to take the front wheel spindle out? looks massive so need to buy one!

Tom

Tom,

I think the GasGas forks are 10mm and the Marzocchi forks are 16mm Allen hex size.

Cheers.

Jon

Link to comment
Share on other sites

 
 
cheers Jon, looks to be 16mm, will get myself off to halfrauds tomorrow to see what ridiculous price ill have to pay for 1 socket!

Tom

If they don't have it, you can make one. Use a short length of rod/tubing and weld/braze a 16mm or 11/16th" nut to the end (a slight angle to the nut makes it a little easier to use).

Cheers.

Jon

Link to comment
Share on other sites

 
Does anyone know what siz Hex key is needed to take the front wheel spindle out? looks massive so need to buy one!

Tom

Tom,

Just to remind you, don't crank the axle in a lot and a lot of riders think the tighter the better. The axle clamp is what holds it snug so it won't back out. If you put too much torque on the axle, it will put a serious sideload on the ball bearings and cause premature failure so about 30 Ft Lbs or 40 Nm should do it.

Cheers.

Jon

Link to comment
Share on other sites

 
 
 
We found an old chisel that was just about the right size :rotfl: surpose it was kinda lucky really .. :banana2:

Also a good idea. Since the hex is a 6-point, you don't need something that is an exact fit. My other bike is a 12-point hex axle so it has to fit fairly snug.

Jon

Link to comment
Share on other sites

 
 

Tom, you do not need the 16mm allen key. I contacted factory Kev on this very issue, and gave up trying to find one.

If you slacken the axle pinch bolts you can loosen the axle nut on the other end, which I recall is approx 7mm allen key, give it a tap through so you can grab hold of the 16mm end, then loosen off completely and pull out from the 16mm end.

This worked fine on my 07 250 without a 16mm allen.

Good luck

Tim

Link to comment
Share on other sites

 
 
thanks for the advice =] In the end I got hold of a 17mm one and just ground it down to fit!

just gotta repair the fork tube now and im all done.

Thanks again =]

Tom

Tom,

If it is a scratch or cut, sometimes they can be repaired with SuperGlue. Clean cut throughly and use SuperGlue to fill the cut, let it set and then take some 600 grit wet/dry on on a flat surface like a piece of 1/2" barstock and sand around tube (not lengthwise and not just in one spot to avoid making a depression and just to restore the area and cut down the raised edges of the cut) and then get a set of forksavers (Neophrene covers) to prevent further problems. It might save you buying new tubes.

Jon

Edited by JSE
Link to comment
Share on other sites

 

cheers Jon, already done that trick, works a treat! I use araldite though not superglue, and 1200 grade wet and dry! (takes forever but worth it). I told Dean Thomas (Ex BSB Rider) about that trick and he had never heared of it, took the fork to show him and he couldnt believe how smooth it was.

I have a couple of fork guards but somehow something managed to get to them!

Tom

Link to comment
Share on other sites

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
  • Create New...