stilly

Hi all just wondering what psi should I be running in my front and rear tyre, I have had around 7psi in both, is this too much or not enough,

hi to all that have helped me with the sherco clutch problem i have had and finally it is sorted, i shaved about 2m to 3m of the rod that gose from the clutch basket to the cyilnder been out to day and its spot on, many Thanks guys a big smile on my face now whooooooooooooooooow.

Grooves in the basket were filed out first before the new clutch went in, all the plates I replaced as they were, none of the plates are offset should I strip done and off set the last plate or not? When everything is back together you have got some movement on the plates in the basket could it be that because the back of the basket aka as a first steel plate then a friction plate and so on, it could mean the basket is worn and a new one is needed, who knows it seems like a un answerable fault I think now should I have bought a sherco ????

I got mine out with a long punch knock it from the inside, soak them with plenty wd40 worked well f me back and front wheels

I have stripped mine down again put it back together the same as it was, no clutch plates looked to be offset, I have removed the master cylinder cleaned it ground a little off the push rod, fresh oil back together sparkling like new but still slips in top gears, I have been told it could be the clutch basket now, I have to take the hole basket off and the bike shop is going to measure it for me could this be the fault ? When I do this I will let you all know cheers for all help

Hi sorry about my Geordie twang ha ha, when I say fist full what I mean is, I will be in 4th gear riding across the field open up the throttle and she just slips so you have to slacken of a bit to let you get going, clutch and springs from offroad moto in Blyth, ipone oil, lever has plenty play and everything has been stripped an cleaned I can live with the problem but it dose not seem right for it to be ok 123 gears then 4th and slips it's a pain in the neck really.

Hi all ? Sherco 250 2004 clutch new plates and friction plates, new springs, filed out the grooves in the basket as advised to, ipone oil as recommended, now it's doing my head in rides ok in 123 gears 4 an 5 it slips when you give it a fist full what to look at next any help much appreciated thanks all.

Sherco 250 2004 starts first kick when cold but I can not start it when warmed up, if I pull the choke on it will fire up straight away, it runs ok when out but don't no why I have to put the choke on every time to start it any ideas ?????

Hi all readers I need advice on what to do next I have put new friction plates in my sherco 250 04 model but it still slips in 4th gear when you give it a fist full engine oil is ipone and I cleaned the steel plates they looked ok but it still slips any ideas what to try next ???

Regarding the new mudgaurd I need for my sherco 04 I am in Northumberland, any close to here don't mind mail ordering,

Yeh I Defo need to get the gears sorted seems like my clutch slips in 4th when you give it a fist full, I have just put new friction plates in and new oil any ideas what to do next,

Bike still runs sweet, changes gear ok finds neutral perfect the track I built with stream sections and logs to get over some steep hills, I can only sometimes get into third needing fifth is not a problem at the moment, think I will enjoy the bike for now as I have just got it.

Hi to all you readers, trials is new to me just got a sherco 250 2004 and I would like to change the mud guard/seat and stickers any 1 know any good sites to buy from, help much appreciated

Thanks I will get my local bike shop to inspect much appreciated, don't fancy stripping the gear box to bits sounds like a job and a half

i get the front wheel up in third gear try it once your up its good to keep the balanceing point right and steady, but its also lots of practice and bottle, you might find yourselve replaceing mud guards ha ha

i say your given a clutch so use a clutch might save you lots of engine problems.

Hi me as well new to trials got a sherco 2.5 last week few hickups with it but I got it cheap I live at Hexham got 3000 acres of woodland on estate I work for mint fun wouldn't look back at motox

Hi trials is new to me I just bought a sherco 250 it seems like It only has 4 gears with a neutral between every gear but no fifth is this a common fault can it be easy fixed any help much appreciated Thanks stilly