kenny123

the bike jus fell to the side but it was on a hill so the bike didnt go right over.

i went out today and attempted a hill i fell of to the side of the bike not causing any damage but when i lifted the bike up and attempted to start it there was nothing. i was trying for about half an hour until it finally started does anyone no what this could be. its a gas gas 200 2003

i got the dexron auto transmission fluid. but is that not for automatics? it also says dexronII on it???? is this the right stuff

al the middle panel is part of the airbox and then there is a small plasitc panel in the middle of it which you can take of to clean the filter

ok so will i have to change the whole air box aswell wont i? is that what u ment?

i am also thinking of changing all my plstics as anybody git an idea of the full price it would cost including the tank stickers and the other stickers?

o no dont tell me that. well it was ok for a few hours after i fludded it so im hoping it hasnt caused that much damage. thanks for the help

ok cheers i will try halfords tomorow. just hope they sell it

ok il get some of that stuff tomoro cheers.whats the ful name of it?

ok Thanks alot for the advice. well i have bought some more gear box oil this afternoon so will try it once more and see how it goes. the oil which is in now is cloudy but not half as much as it was when i drownd it. but the gears are working fine so am i best just leaving it or could it cause more damage

ok cheers. someone told me to pour engine oil in to eventualy get rid of the water? is it easy to change the water pump seal and how do you do it? sorry for keep askin but im not very good with bikes

so what am i best doin then. lol

will the seals have worn because of the water that has got in or would they have been worn in the first place because al was fine before i flooded it. the water literally covered my bike

hi. i was out today and was riding in the stream when the front end of my bike droped of a ledge. the water more or less covered my handlebars. i managed to eventualy start it but could it have caused any damage. i gave it a good pelt over the moors and all seemed ok. when i got home i realised that water had got into the gear box oil so i drained it and changed the oil but the oil has gone cloudy again. what is the best way to get rid of the water? is it to keep changin the oil? thanks. its a gas gas 2003 200 pro

hi everyone. i have a gasgas 03 200 pro and i have sealed al round the airbox but mud and water seems to stil be getting in through the air intake. i see that there is a part available which stops dirt from flicking of the front wheel straight into the airbox. does anybody no where i can get this part from or has anybody got a spair one that i could buy? thanks

il buy it if scott doesnt want to buy it/

hi i have a gasgas pro 03 200. i was out today and snapped my throttle cable. i have also released that wer the adapter that joins the carb to the air box isnt closing up proply and there is a small gap which is letting crap in. can anybody give me a hand on how much i will have to pay for a new cable and some kind of adaptor for the airbox. any help would be appriecated.

whitworth quarry

hi. cheers for that. put new gear box oil in but still no result. the gear box oil i used is silolene pro SRG 75 100% ester synthetic racing gear oil 10W-30. anybody no the best way how to bleed it? thanks

hi sorry its a gas gas 200 txt pro 03

hi. just attempted to fit new clutch plates and when i took the casing of and took of the 10 bolts 2 of them rounded but i managed to eventualy get them out. so need to order new screws. But the clutch plates i have taken out because the bike was draging realy bad look in as good condition as the new ones. if the new ones dont solve the dragging what else could it be. any suggestions would be appreciated. thanks

god nos which type they are. the bike is an 03 200. i jus rang gasgas and asked for clutch plates and gasket and thats it. i have been told to turn the bike on its side and just undo the screws and take it of and just replace the plates. does it then need bleeding. cheers

hi. sorry for asking for al this information on my clutch but i have just recieved the clutch plates and the gasket.i am not any expert on bikes but have a slight idea. could anyone please tel me what i do to fit these parts. thanks

bit to far.cheers anyway

hi. the man i usualy use to get my bike fixed is away and is fully booked for about a month so i am urgently needing to find someone who will be able to fit a new clutch or clutch plates watever it needs but i cant find anyone cheap enough in the area of manchester could anybody help. would sandifords be a good option. its a gasgas 200 2003 thanks