Jump to content

zaccyboy

Members
  • Posts

    23
  • Joined

  • Last visited

Contact Information
 
   
  1. Hi Guys and Gals, The question is.. just acquired a gassa 250 txt pro on a 05. The clutch has been redone about 3 weeks ago by previous owner ( done by shop )The clutch feels very tight at the lever ( pulling lever in). Any ideas on this would be appreciated. thanks all.
  2. zaccyboy

    Beta Rev 4

    Hi TC, Iv been running gas gas txt pro 250 ( 06 )Im thinking of changing to Beta Rev 4 ( 07/8 ) I know the difference between 2 and 4 strokes but I wondering what you guys think? Any advice on the Beta ( running it etc ) would be great. Gas or Beta ?? its over to you guys. Thank You Zac
  3. Hi Scotty and welcome to trials, the woods at pea farm are a good place to start. Nothing to demanding. I often get down there so if you's fancy a trip there give me a bell. Zac 07809375069
  4. Hi Folks, I own a Peugeot 1007 fitted with a Swan neck towbar, Im wanting to fit a bike rack instead of lugging a trailer around, anyone know of a clamp that fits onto the swan neck to allow the fitting of said bike rack. Thanks Folks
  5. zaccyboy

    BETA REV 3 OIL

    Hi, much covered topic, which is the most suitable oil for 2003 beta rev 3.Currently usin SAE 75 THANKS ALL
  6. Billy T - The knocks/clanking is when throttle open, I also wondered if the prob was merely the engine was at its max!!!! I will try higher grade fuel at weekend and keep u posted with the results thanks guys
  7. Hi iv got a beta rev 3 on a 2003, when I put her under load ie up hill climbs the engine knocks, could this be a fuel grade prob or timing? I use unleaded but Iv read that Beta's like a higher grade fuel to run better, any experiences on this? Re timing any views on this? Thanks
  8. Any advice on controlling bike down steepish narrow slopes and banks? I seem to flap abit when atemping these and usually make a complete clown of myself and slide off, which brake to use and body position would be a help to start I guess, also bar and lever position( beta rev 3)would help too. CHEERS GUYS
  9. Hi Ham2, where ya from mate? Im from Blyth,you ride local like?

  10. Lime Kiln Woods.... anyone help with info and contact number/s if reqiured please.

    1. ham2

      ham2

      Oy,oy..Located at Ryton,not ridden for a while..got no transport and mates don't have room ont trailer....I'm working on it though!

      Wayne

  11. Hi mate, Iv tried to find rayc on forums re trials schools in the northeast of england but to no avail, can you point me in the right direction if poss. cheers mate
  12. Hi all, anyone got any info re trials schools in Northeast England, anyone help?
  13. Thanks guys, re tomorrow,I will pm you mate maybe get somemore tips off you at rothbury. thanks again guys
  14. Hi all, Well i entered my first trials today at Consett - Hownsgill Farm, well I was geared up for it,tagged along with another lad to the first section and thats where it all pear shaped lol. I learnt 2 valuable lessons here, 1, spend more time watching riders ride the section and have the bike positioned correctly lol,I did neither of these and that was that lol OFF !! twisted my left knee so that was my entry at trials, but rather than give up I followed the guys around the course and WATCHED..I managed to get an hour and a half on the bike before my knee give up and I was goosed lol. I will try again tomorrow at Rothbury.... this time watching and learning!!! Prior to today I only spend about 2 hours riding over 3 outings on the bike so Im pleased i managed the hour n a half to be honest lol. Any further advice would be very appreciated guys.
×
  • Create New...