danbillam

what did you do to the 13 to give it more off the bottom?

does the new one have more grunt or is it still too soft off the bottom?

have you gone for a 300 again? I fancy a new one next year although I like the look of the new ones a lot.

cheers mate I was in the shed first thing this morning I looked at the beta spares and seen the order and already had a feeling it was that. started it up at the trial and ran perfect all day.

that may be the problem thinking about it. the brass needle jet did fly out but I noticed and put it back. although I put it in from the top of the carb. should it go in from the bottom under the main jet holder?

ill give it a go tomorrow the pilot jet is clear so must be inside the tower where its blown deeper in to the small hole exit. ill keep trying to flush it out before opening it up

would I be right in thinking theres a bit of dirt trapped near the tiny exit hole and be better getting the security torx fitting to clean inside the tower better?

the carb needed cleaning on my evo 300 so I stripped it down and carb cleaner and air lined it all jets etc was clear. put it back together and it will tick over but bogs down or dies when revved. it will run nere on perfect with the choke on or the air mixture screw all the way in. ive stripped it back down a few times and cleaned it again but I'm thinking a bit dirt is trapped beneath the pilot jet which I cant seem to get out? do those security torx screws need to come out or is there a specific way to blow through that circuit? ive got a trial tomorrow and going to have to borrow my dads carb but want to get this sorted asap.

Even if the master cylinder is completely empty I thought it would have had a air in by now

my brother has just bought a 16 ice hell. we was swapping the master cyclinder covers over to some nice red csp ones earlier and noticed the clutch master cyclinder was completely empty of fluid. which seems weird as it worked when I test rode it a few days ago. I'm presuming it will need bleeding rather than just topping up as its completely empty up top. and how are these bled? there isn't a nipple near the casing where the hose is like on my beta. thanks

cheers mate ill grab some then.

I want to fit some boyesen carbon reeds to my 16 evo 300. on motomerlin etc the carbon reeds are listed for only 09-14. are they not available for 15 onwards or do they still fit? thanks

Also got a medium and fits true to size. Very comfy helmet and don't even know its on after a full day.

stripped cleaned and regreased thanks mate. its back on now but looking at it the dogbone bushes and bearings are about ready for being replaced.

cheers mate. I think ill pop the wheel out aswell for a bit more space.

after a trial today I cleaned the bike and noticed a nut on the rear linkage was a bit loose and theres also slight bit of play from somewhere on the linkage. I'm going to get it apart and regrease tomorrow tightening it back up. any tips you've found to help with this job to make it easier or things not to do. bikes 2016 but should imagine same applies to all evos. thanks

has it got a flywheel weight fitted? you could also alter the gearing. but to be honest id get used to it without and the bike will be a lot better. I have the same bike and thinking of getting carbon reeds and a ti front pipe to give it a bit more off the bottom end.

not sure on those but I have the gore tex gearnes. only had them a few weeks but very comfy and no problem paddling through streams.

I've only had it 2 weeks so was already like it mate. Anything to bring them back or is it not possible.

On my 16 evo the black bits of the wheel rims look all white and milky. I'e noticed it on other not just mine. Anyone know how get them back looking good? Thanks

Splatshop has 2 stiffer springs to fit your bike mate. Did mine a few weeks ago

hi mate, ive done about 10 hours now with the 20% stiffer rear spring and the front with just preload changed. seems to be well balanced and feels good when riding

yes it is mate must be quite a bit smaller. it only fits corner to corner so the other bike would have to be right up to it the way and touching to maybe fit.

have you got a picture with 2 bikes in mate? it must be a bit bigger than mine unless I'm being thick

I think there is only one model for combo I have mate.