Jump to content

Andyb1987

Members
  • Content Count

    32
  • Joined

  • Last visited

About Andyb1987

  • Rank
    Member

Previous Fields

  • Bike
    Montesa 315r

Profile Information

  • Location
    Durham

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Andyb1987

    315 Pistons

    Thanks for the reply I think thats to complicated for me it will be easier to buy the dykes ring etc and have them machined to suit.
  2. Andyb1987

    315 Pistons

    Can the cylinder be bored to take a different piston like a beta for example
  3. Andyb1987

    Montesa 315r oko carb

    Where did you get it from
  4. Andyb1987

    Montesa 315r oko carb

    Hi all which oko carb are people running on there 315r currently got the phbh 26cs which has seen better days. Thanks in advance
  5. Andyb1987

    2 stroke oil

    What ratio oil to fuel should used when there's roads and big banks then surely 80:1 is too little
  6. Andyb1987

    Montesa 315r kickstart idler

    Stripped down clutch casing today to inspect the plates i took the whole side casing off and the kick start spring didnt look right is was touching the outer basket so I removed and cleaned the kick start idler gear. The question is though when I put it back together do i have to put any tension in the spring buly winding it half a turn etc or do i just fit it straight in the hole as is? Pic for attention Thanks in advance
  7. Andyb1987

    Redex octane booster

    Ok thank you for your input I wouldn't know how ir where to start to get a head spacer made I did how ever put an additional base gasket of 1mm on the bike to no avail.
  8. Andyb1987

    Redex octane booster

    Increase base gasket size cleaned all carbon from head piston and exhaust carb is jetted to spec in manual running out of things to do
  9. Andyb1987

    Redex octane booster

    Have you found any cure
  10. Andyb1987

    Redex octane booster

    Has anyone used redex 0-60 octane booster in a 2 stroke to cure pinking?
  11. Andyb1987

    Beta rev3 250cc piston sizes

    Can anyone tell me what size pistons you can buy for a 250cc beta rev3 i know that a size D is 72.481 but what are the others also i need to know the gudgeon pin bore aswell does any one have a copy of the technical data page out of the owners manual. Thanks in advance
  12. Andyb1987

    MONTESA 315R '97-'99 CARB JETS

    Thanks Thanks it currently has a 120 main 46 upper 46 lower needle clip is correct yeah thanks big help. Will order a new main straight away
  13. Andyb1987

    Modifying A 4Rt Rear Mudguard To Fit A 315R - How?

    No I haven't set the squish don't know what is meant to be? What difference will altering the port timing make? Where could I get the 1mm head spacer? Would a thicker base gasket give the same effect currently got a .5mm base gasket and pinking issues. What's driving me crazy
  14. Andyb1987

    MONTESA 315R '97-'99 CARB JETS

    What is the standard jetting for the early 315 '97-'99 PHBH 26CS CARB? Only manual I can get is 2002 which has the newer carb
  15. Andyb1987

    Modifying A 4Rt Rear Mudguard To Fit A 315R - How?

    What difference will altering the port timing make? Where could I get the 1mm head spacer? Would a thicker base gasket give the same effect currently got a .5mm base gasket and pinking issues. What's driving me crazy
×