Gas Gas

Quite the pain in the butt! All the fun of fishing a hose through the swing arm, and then of course the notorious bleeding! The replacement hose wasn't exactly like the original. The Original hose had a longer solid line section at the MC, with multiple small bends.. Anyone ever see that particular version of the hose? I did dig about online with no real luck. Good part is, I have a rear brake again!

The fork tubes on my 2000 TXT 280 are bent. The tube has a dent in it, so I suspect not repairable. Does anyone know if replacement tubes are available? I have looked on the Gas Gas parts list, but could not see them listed.

I need some main fork and dust seals ('12 GasGas 300 with 40mm Marzocchi forks), most of the trials websites and eBay don't seem to state the seal brand so I assume they are just selling cheap generic seals? The Pyramid Parts website does the whole kit for £17 but I've read that the seals can be junk. The only other branded seals I've found are SKF but they are about £50 IIRC for a full set of main and dust seals. So what are you lot in the UK buying?

I am getting my new Gas Gas 270 on saturday morning, and i was just wondering if anybody has some different styles and colours of stickers which i can put on my bike?

ive got my lad a boy 50 in superb condition but noticed that the fan is not coming on, ive tried bypassing the thermo switch and it still wont work and ive tested the fan with a battery and it all works fine so my question is what else can the problem be, thanks

Hi All I have just got my self a 2000 txt 200 and i am going to change the gear box oil on it. Does anyone know how much i need to put in. thanks beanie

Any idea where I can get a touch up pot for the above folks? It's the standard Gas Gas red frame. Cheers, Paul

I am getting my new Gas Gas 270 on saturday morning, and i was just wondering if anybody has some different stickers in which you can post to me so i can put them on my bike?

Hi all could anyone tell me the best 2 stroke oil and mix ratio for the 70 rookie . New to us bike and not sure of mixture. Regards Neil

Hi everyone Is there anybody who could assist me please I'm rebuilding a 1994 JT35 and where do I buy full gasket set and all the bearings for the frame and seals ????? regards Alex

Hi all Just got me a 2004 300 Raga and its the dogs! I'm new to this trials lark and have spent a short time riding a 2yr older Sherco 250 but fancied something newer and with a bit more punch. Took a bit of getting used to after the super friendly Sherco engine, but after my Honda XR-650 even this Gasser is quite tame. Obviously trials is a very different environment to enduro but had a good play on the bike over the weekend and the power delivery really seems spot on to me. It will chug up anything at low revs in a very controllable manner. The Gas Gas finish is however appalling..... The magnesium cases and swing arm look pretty rough, but hey the bike is made…

My chain came off today and started to coil around the front sprocket snapping the little alloy crank case breather off I have the right angled bit, but the part that pushes into the crank case has fell inside the crank case. Any ideas how to get it out other than pray it comes out with dropping the oil. Can I take this side of the crank case off or do I have to start with the clutch side and work my way back. Many thanks

Hi does anyone know of the correct jets and slide pin for the txt 70 cc Regards Neil

I have replaced a damaged kickstarter cover last friday, and too badly also saturerday whole they. Took a s3 one and mounted without problems, bled the system, nor worries. Untill tried to start it the kickstarter did not went smooth enough (did start and worked fine for the rest) Spend hours dismounting and mounting parts to figure out where the problem was. Without the clutch no problem, with it it was too thight. Without the crankwheel no problem, with it it was again too thight. Searching searching etc. Finally sunday morning, replaced the kickstarter spring, the cup where the spring is in. Not stuck anymore, but now the kickstarter would not grap (the…

I have a question about my front end of my TXT200 trials bike. I noticed that it is very "springy" for lack of better words, and no matter how much I adjust the compression damping or rebound, to no avail does it reduce the "springiness" of the forks. The only work I've done to the front end is replace the seals and dust caps. I'm wondering if the adjusting cap which threads onto the adjuster top return rod (runs inside the spring) could be tightened down too much? Nothing else has been adjusted, spacers are stock ect. Same amount of fork oil, and same viscosity. I noticed that the cap threads into the rod and then intot eh fork tube up top. Perhaps I can back off…

Noticed the Gas Gas dealer I use, in Oregon State, has anounced 2020 models. My 2017 doesn't need replacing, but good to see KTM is working toward keeping Gas Gas trials alive. Art

Hey guys, Taken the clutch apart and was wondering what's the proper size for the clutch pack? Also i may be needing to buy a new set of plates and springs soon, where can i get tham from that are fairly cheap? Cheers Guys Merry Xmas

Hi all, I've have just bought a 2008 Gas Gas 125 racing.its In mint condition and rides great. Are there any problems whith this year I should look out for. Are the oils that I used in my sherco good for this bike or what would you reccomend.and any general maintenance tips would be great Thanks, Ben

has any one trial a gasgas randonne as i am thinking of getting one i have ty pinky now and thinkin of selling to buy one so i can use for light off road and maybe a odd B trial,has anyone had any issues with these bike i should know about

Hi, I need a new master cylinder for my 2005 280 pro, Will any trials bike M/C fit and work ?