Jump to content

wright4d

Members
 View Profile  See their activity

  • Posts

    76

  • Joined

  • Last visited

 Content Type 

Posts posted by wright4d
 
 

  2. TY 175 Swing Arm

    in Yamaha

    Posted

    12 hours ago, feetupfun said:

    Width at pivot including end caps 178 mm

    Length from centre of pivot to centre of axle slot 380 mm

    Thanks for that,  I bought an aluminium swing arm made by Kato from Japan and it was sold as for a TY250 but now it's arrive it looks like it is from a TY175 which your dimensions have confirmed.  Many thanks 

    • Like 1

  4. TY250 Kato Swingarm

    in Yamaha

    Posted

    Any of you guys know whether Kato did an aluminium swing arm for the TY 250,  I have seen one advertised but any of the pictures I have seen only show the 175's he did with one like it on them

     

    Thanks

  7. TY250 Front Pipe

    in Twinshock

    Posted

    I've got a question for all you guys who've fitted after market front pipes to your Yamaha TY 250's (Majesty's or not)  I see there are basically 3 variations, standard, long (where it exits goes to bike left side up then over and back to right side and short where it exists and comes up through the front framer tubes and back to middle box.

    What are the pro's and cons of each from a bike response / riding style perspective.

    Also is it a must to have the WEs mid box with either the long or short variation?

    Thanks

     

  8. Lower Foot Rests?

    in Honda

    Posted

    On 12/29/2004 at 4:20 PM, the artist formerly known as ish said:

    Did mine on the RTL well worth doing.

    Marky won't your hand get tired :wacko:

    Hi

    Just reading through some old posts on foot rest modification, I have a TLM and want to do the mod also what dimensions did you move it back? and down?

    Thanks

     

  9. RTL 250

    in Honda

    Posted

    7 hours ago, barfy said:

    What age RTL is it?

    On the twin disk model a Montesa 4RT, Sherco, etc. sprocket will fit. I run a 9 to 42 setup but this does need a 1/2 link. 

    Cheers

  12. Raga 2011 Advice

    in Gas Gas

    Posted

    Hi All

    Looking to sell my 2011 Raga,  it is registered as a 300cc but I have had fitted recently a new 250 Barrel, Piston and Head Insert.  Runs great and so much less tiring to ride.  Do you think I should put it back to 300cc to sell or just sell as a 250 but as long as I state it's registered as a 300cc should I be ok.

    Cheers

     

  13. Beta 4T Head Gasket

    in Beta

    Posted

    Some years back I had water leaking from just below the water pump housing, I thought it was head gasket and had it changed but still leaking turned out to be the outer water pump seal which leaks into a cavity between the inner and outer seals and come out through a special hole to prevent water entering the cylinder

  14. Is There Something Special

    in General Trials Talk

    Posted

    I needed a new air box fastening countersunk screw for the gasser so looked on dealer websites and they are £1.20 plus postage each.  Screwfix have stainless steel ones for £2.65 for a bag of 50.  Is there something special about the originals or am I missing something.  I like to give the business to the dealers but this is taking the p a bit.

    • Like 1

  17. Gas Gas Decals

    in Gas Gas

    Posted

    Hi All

     

    Anyone know where I can get a full set of 2011 Raga decals,  time to freshen the old girl up a bit.  I really would like to keep standard look but if I have to I would go for later years.

     

    Cheers

  25. Trials Top

    in Trials Gear

    Posted

    Hi All

     

    Looking for opinions,  want to get a trials top to wear over my normal riding shirt when its a bit nippy but wearing my proper jacket will be too warm and sweaty.  Any trials specific options or I have seen a Berghaus micro fleece in go outdoors.  what do you think.

     

    Cheers

  
×
  • Create New...