Skip to content
View in the app

A better way to browse. Learn more.

Trials Central

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

burns1989

Members
  • Joined

  • Last visited

Everything posted by burns1989

  1. Ok sounds like you have still got a carb ration issue . Or a crank seal gone on the left side of the engine causing oiling up of the plug . I went out on my beta last week and Wass on it for 5 hours and it rode perfectly constantly all day . With it not responding when u try to wheeli sounds like it's bogging out and has no power antill it clears out the unburnt oil . Does it idle , or you could find the float hight is too high flooding the engine on the steep hill decent . Trick one to diagnose with out being there
  2. Hi have you had any luck yet with your bike
  3. burns1989 replied to burns1989's topic in Beta
    And a pic of the outer cover with the two coolant pipes . So i'm not sure what's going on as the new cases for the 06 rev don't have the hole in it its blanked off .
  4. burns1989 replied to burns1989's topic in Beta
    And a pic of the outer cover with the two coolant pipes
  5. burns1989 replied to burns1989's topic in Beta
    This is what my casing looks like with the hole on the left of the water pump casing but this is a picture of a 2001 engine just so every one knows what im on about as it may not make sense what im on about thanks ian
  6. burns1989 replied to burns1989's topic in Beta
    Ow ok so it has two water passages as I thought some one might of put a 2001 engine in the 06 frame .as the water flows from the pump to the block though the engine with out two pipes . And looking at new cases for a 06 the hole is blanked off that goes through the case to the crank casing which made me think iv got a wrong engine for year of bike . Thanks ian
  7. burns1989 posted a topic in Beta
    Hi just wondering what the water passage through the clutch case is for or should it not have one as I do need a new case as mine is corroded,if you remove the water pump cover to reveal the water pump to the left of the water channel it has a hole through to the other side of the engine . it has two coolant pipes on the water pump cover so im confused to where the watter flow goes should it circulate from the pump through the coolant pipe to the exhaust and up to the head or does it circulate the water round the exhaust to warm it up faster . thanks
  8. Ok sounds right . Worth checking the fan isn't running when you first start up the bike from cold . Hope its just in need of a good run and works out good for you
  9. Ok how much oil are you adding to the 1 liter of fuel at a time
  10. hmmm I wonder if you have a crank seal gone or your statore could be going as this would cause a weak spark under load , my plug is 7 and il look at it tomorrow to see what its burning like .are you shaking the fuel properly to mix the oil up , how are you mixing the oil and fuel. and are you turning the choke off as soon as it starts and not ridding with it on , sorry for all the questions just trying to cover the basics
  11. burns1989 replied to burns1989's topic in Beta
    Pic of yoke
  12. burns1989 posted a topic in Beta
    Ho all what is the numbers for on the bottom yoke or has my bike got data frame numbers for theft registered bike ?
  13. Don't worry we all get caught out no one knows every thing we only can learn from mistakes . I just recently bought a 06 rev 3 250 and missed a slight water leek which should have been picked up but is my fault for not taking a torch .but every one on here is verry helpfull so your not alone . Hope it runs sweet as a nut
  14. Ok sounds good but hey seem to have leaned off the main jet . Rather they should have made the pilot jet smaller as your main jet only controles the fuel mixture at full throttle . I would check the needle hight as well to see if it has been dropped to try and lean off the fuel or lifted as some get confused where to put the E clip . I would set the main jet back to 150 as it was set up to run the oil mix at 66.1. Yha i would lift the wheel up to check for binding as well if it's not just rough the pads up as it could be glazed up
  15. Hi just a pointer running less oil will make the fuel mixture rich and running more oil will lean off the mixture so if you want to use less oil you should adjust your jets to suite plus different temperatures will affect jetting and running , the pilot jest screw is only going to richen or weaken the pilot jet off idle , you should ring beta uk to see what oil fuel ratio you should run with the jetting if its stock , plus two stroke engines don't like to be ticking over as you need to get the heat in to allow the pug to work correctly to burn the fuel off , a perfect air fuel mixture and right jetting should coulor the plug a biscuit brown and you know you are spot on . but I don't think you will be able to see that as the engines are never flat out . if it were a oily plug id say too much oil but your plug is sooty suggesting its too rich , id drop to the next two sizes smaller on the main jet and on the pilot jest and see what happens . I use rock air filter oil soak the filter squiz out the excess oil allow to dry for 24 hours and its all good and use the air filter cleaners as they do not melt the foam and get all the oil out. check the ignition timing is spot on as well could be slightly retarded
  16. burns1989 replied to burns1989's topic in Beta
    Well the bike rides ok it's just the poor information given with watter leaks . The other funny thing was I checked the wheel bearings and the rear had play and ge said he had just replaced them and he blatantly had not as well as the gear box oil had been changed but had not as it is dirty brown . And I can't even give him feed back on ebay . I'll ring him tomorrow as there are alot of bikes 100 quid cheaper that are in a better condition.
  17. burns1989 replied to burns1989's topic in Beta
    Well I'd rather know if I'd been done in so that I can have a go knowing im in thright
  18. burns1989 replied to burns1989's topic in Beta
    I have sent him a txt but had no reply so ill water till Monday as he said he was going away this wkend . Just hope he helps out
  19. burns1989 replied to burns1989's topic in Beta
    Ok it's 181522419432 just found a watter leek clutch casing has been bodged not happy payed too much for it
  20. burns1989 replied to burns1989's topic in Beta
    Well the power isue could just be me as im used to my mx bike rm 250 and that lays down the power Pritty hard at 50 brake but I gues a trials bike is less power but more torque. Or could it be down to how it's been geared down as 1st is all most like walking pace . Does any one know the standard sprocket sizes .chears ian
  21. burns1989 replied to burns1989's topic in Beta
    Hi thanks did that frame check and it sais it was made in 05 but the stickers show it's a 06 . I gues its preproduction ready for 06 market . How do I post a picture of it on here .Ok my front pipe has a seem all the way to the joint of the next joint of the exhaust .
  22. burns1989 replied to burns1989's topic in Beta
    It's a 2006 with black forks Was off eBay iv herd the 10th number is the year of the bike but not sure if it's true as it would make it's a 2005 .
  23. burns1989 replied to burns1989's topic in Beta
    Yha i know but it doesn't say the cc any where just looked at the Web site and it doesn't show anything to check fram and engine numbers . Just got righting but nothing to state cc . Seems stupid to not have anything to say what it it
  24. burns1989 posted a topic in Beta
    Hi how do you tell the difference of a 125 and 250 rev 3 as it does not state any where to say what cc it is . And my bike seems not to have the same pull that my techno had and seems abit tame
  25. burns1989 replied to burns1989's topic in Beta
    One other question how good does it work with a fly wheel weight as in make any much difference

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.