|
-
I have a 2004 rev3 250cc, how much engine oil should I add or is there a certain level on the inspection window o should be aiming for? Also the other day I could hear a sparking/ arking sound, after looking I could see sparks coming from the top of the coil where there is a connector. Any ideas what is wrong and what I need to do to sort it?
-
Currently trying to source some rear seals for my 2004 beta rev 3. Anyone know where I can get a kit or anywhere else I can obtain these seals?
-
Update,
After drying the plug and heating it up over the cooker, she started faultless.. so now the conundrum is do i carry on and see if it stops again and then get the stator done, or do I do that now and not risk it...
-
-
Was out last weekend and the bike was faultless till the last hour when she decided to just stop..
Got it hope and it started but with a clicking sound and kept cutting out, then she wouldn't start and had no spark. Took it apart and whoever fitted the kill switch was bodged in.. sorted all the wires and did some soldering and the spark is back, rebuilt and she started first time for 6 seconds and now won't start again.. I have a spark also..
What do I need to check?
-
Bought a Beta rev 3 a few months back and it had terrible clutch drag, would take at least 10mins of warming up before it was rideable. Now after doing this mod I can start the bike up and the clutch works straight away with no drag...
Great post!
Many Thanks Jamie
-
Will order a standard one, probably damaged in the past and someone has made a replacement..
Cheers Jamie
-
Took the bike to the local shop to have the rear brake bleed, on picking it up they mentioned that it was a right pain to bleed and believed that the bar that goes in the master cylinder was to short.. Went out on the bike on Saturday and the rear brake was hit and miss, some times it worked then nothing, you could feel through the pedal like something was slipping...
So before I buy one on ebay as they don't tell you the size of the bar, does anyone have one to measure on theirs?
Mine is around 123mm
Cheers Jamie
-
I have cracked it open a little and then doubled on the amount open until the fluid leaks out the nipple..
-
I stripped the bike down to give it a full clean, so now rebuilt but the lines have no fluid in.. I'm more at a loss as why the reverse bleeding isn't pumping in the fluid..
Jamie
-
Good day all,
I am getting no where trying to bleed the clutch and rear brake, tried both with normal pumping of the levers but not getting any air or fluid to move. Also tried the reverse method on both and no matter how hard i push on the syringe I am getting no fluid in, I can feel the resistance and when I let off the pressure I get some old fluid pull out into the syringe.. Any tips before I have to resort to paying for it to be done.. I only did my zx6r last month and that was a dry system with no issues..
Please help haha Jamie
-
-
Bash plate was a bitch but shes on now, now for the radiator
-
Going to try that, t's about the only way I haven't tried
Cheers Jamie
-
Having a nightmare putting the front end back together, it's like an episode of krypton factor..
What order does it go together out of the radiator, exhaust and engine-radiator-engine guard brackets..
All bits in the picture..
Kind rgds
Jamie
-
Anyone know the torque for the clutch spring bolts on a beta 250 2004 model?
Cheers Jamie
-
Cheers both, my mistake its a rev3 not evo..
Also found the following on this site
had a file with these in, think i may have copied it from a previous post
Tightening torque Rev3:
Shock absorber-Swingarm 45Nm
Shock absorber-Frame 45Nm
Connecting frame rod-frame 23 Nm
Cylinder-Crankcase 20-23 Nm
Primary drive gear 120 Nm
Handlebar 25 Nm
Engine-frame 50 Nm
Swingarm bolt 90 Nm
Front wheel axle 65 Nm
Rear wheel axle 65 Nm
Steering stern bracket 25 Nm
Rear fender bracket 10-15 Nm
Front brake pad 20-23 Nm
Rear brake pad 20-23 Nm
Engine Head-Cylinder nuts 15-16 Nm
Front axle fixing nuts 10 Nm
Flywheel 140 Nm
-
Evening all, bought my bike at the back end of 2019, being a novice I did a practice day at nant ucha and loved it.. Done one competition which was challenging to say the least, then the local club had to cancel the other dates due to the weather and then we had covid.. so with loads of free time on my hands I decided to give it a good strip down and clean..
Also if anyone is good at identifying bikes, I can't remember the year of this ?
All the best Jamie
-
Anyone have any kind of downloaded manual or torque guide for a 2007 beta evo ?
Cheers Jamie
|
|