|
-
Hi all
Just stripped my front steering,to find the bottom bearing being very notchy,should there be a seal at the top,as the bottom bearing is very rusty?how do you remove bottom bearing from the bottom yoke?
Cheers
-
Hi all
Thanks for all your advice,problem is i cannot decide if to watch 2 days of the pre 65 and 2 days of SSDT,or just the SSDT?Comments...........
Cheers
-
This is good timing,have you found a supplier?i am going to change my rear spring on my EVO(SXS sell them)how do you set up the spring length?
Cheers
David
-
Hi all
I am going to attend this years SSDT,but want to make sure i get to see two sections,being:The pipeline and the other is one that is always featured on DVD's,it is were they go under a road bridge which is always full of spectators and climb up the stream over rocks.I hope this is good enough descripton.My main question is were are both of these sections so i can plan to see both,also are they at opposite ends of the trial,or by any good luck,within a couple of days of each other.Any help would be great.
Regards
David
-
Just got from under the table,to avoid the flack......................thank you all for the advice,it is all very useful,thank you again.
Regards
David
-
Hi
Just removed the ignition cover on my EVO 2010,to find alot of water and condision insided the cover and over the flywheel.
Is this a problem or just damp that has built up over the winter,any tips on keeping dry,or just leave it as it is and just dry out every few weeks?
Regards
David
-
Hi
Did you get me email address earlier,if not it is david@ellary.freeserve.co.uk,would be realy gratful if you could send them.
Regards
David
-
Hi
Did a trial on the 21st of november at stokechurch,were can i get the results from,do they have a website?
Cheers
-
Hi all
My clutch on my evo is heavy,i have read about removing two Questions,does it matter which two i remove,do i remove springs/caps/bolts?
Cheers all
-
Hi all
My clutch on my evo is heavey,i have read about removing two Questions,does it matter which two i remove,do i remove springs/caps/bolts?
Cheers all
-
Silly me to expect something you buy to work as it should.....................thanks all.
-
Thank you all for the replies.......................
-
-
Hi all
Since buying my EVO 2010 250,i have been made aware that the swinging arms develop cracks,is this correct?were should keep an eye on?
Regards
-
|Hi all
Just bought a new 2010 EVO 250,i am experiencing the same problem i had with my REV3,when the engine running,when stationary with the engine running,it is very difficult to change gear,let alone find neutral,alot better with out engine running.On my old REV 3,i did the clutch mod,which made it alot better.Surley i should not have to do this to a two month old bike??????????????????
Cheers
-
Hi
Thanks for that,but need more general advice on adjusting these settings.
Cheers
-
Hi all
Can somebody help with the Marzzochi forks,on one fork it is marked C,the other R,any help would be great?
Cheers
-
Thanks so far.......................but i need to use C/R on the first repl?????????????
-
Hi all
Can anybody give me the ball park adjustments for my forks,one fork has c on it,the other r.
Cheers
-
Hi all
Sorry for all the questions.
How do i know if i have a slow action throttle,as this bike(XISPA 250) is far to powerful for me !!
Cheers
-
-
Hi
is there listed any were how to change oil seals on this forum?
Cheers
David
-
Hi
How can i find out the oil quanity level in the front forks of my 09 xispa ,i want to change the oil and stiffen them slightly,any recomendations on increase levels of oil?
Cheers
-
Hi
I have a 09 XISPA 250,fitted with a OKI 28mm carb,it is not running well from pick up,ok when on 1/4 throttle and more,any set up hints,i have dropped the main et as advised by vince.
The bike is very poerful for my beginner status,any way of softening the power ?
Cheers
-
Hi
What is the name of the belstaff jacket worn by S Miller etc in there hey day,i won't to buy one,but want to get the right one.
Cheers
|
|