b101uk

550ml of oil should weigh less than <550 grams or oil wouldn

I cannot get my clutch MC down the bars far enough without it restricting how far I can twist the clutch MC down due to the MC pipe fitting hitting the lower part of the handlebar bend, if I twist clutch MC down to the angle I want the lever there is to much lever length over the hand grip for my liking or the handlebar is rolled to far forward with the right lever length and I am using a short clutch lever. They are Renthal 660

Photographs on ACU trials licences! I am waiting to hear back again from the secretary of the ACU with regards as to under which article of EU/UK law gives the ACU has the right to require a photo for the issue of a licence or to discriminate agenised me or others if I/we refuse to submit a photo on the bases faith/religion, personal beliefs, phobia, ethical grounds, protection of ones own personal data or that I have higher forms of proof of my identification. .

The ability to read and write like age is no guarantee of wisdom or the value of ones words or your moral standards! I couldn

Check the pads are wearing parallel to their backing plate, if the pads are wearing at an angle it can cause the pistons in the calliper to cant at a slight angle when applied causing stiction between the calliper body & piston. Other than that if its lack of use take the calliper off the fork and the pads out, get a toothbrush to clean any dirt/etc of the end of the pistons and give a little spray with WD40 then manually push them in, temporarily put the pads in and refit the calliper over the disk and apply the brakes to extend the pistons agene then repeat manually push them in - repeat a few times, on the final time wipe off any excess WD40 or use brake cleaner so dirt/dust wont stick to it.

Start by setting up the suspension sag Like in e.g. http://www.trialscentral.com/forums/index....showtopic=32260

So dose S4C do English subtitles for the English speaking Welsh contingent (and the non Welsh speaking English contingent!) Was listening to radio 4 a couple of weeks ago and they were on about how S4C broadcast lots of programs ware the official viewing figures was 0 viewers (excluding kids programs which viewing figures are not collected for) so if enough people view trials via S4C on sky with the program theme of

Why not check over/service the fuel tap, if it runs ok in the

It is most likely that the piston in the master cylinder is not returning fully, if you have checked the clearance for the lever is ok, remove the lever and the rubber dust seal and check theirs is no dried mud or a bit of grit, sand or rust behind the circlip that holds the piston in the MC which is stopping the piston returning fully

I would buy one because NOT everyone who buys new off-road bikes competes thus WOULD NEVER have registered it with the ACU/AMCA in the first place! Like most things like ID cards etc they only mainly penalise the innocent person by burdening them with extra hoops to jump threw. With respect to stolen new bikes, if you bin the frame with the VIN on and the relevant half of the crankcase with the engine number on then you have plenty of untraceable parts to sell, if you wanted to keep the engine complete its extremely easy to get the

WD40, spray on, leave to soak for 20min, spray a little more then rub with a cloth. Works ok on plastic, paint etc.

There should be some clearance between the end of the master cylinder piston and the lever adjuster that pushes the master cylinder piston in, the clearance is there to allow the master cylinder piston to return fully allowing fluid from the reservoir into the master cylinder chamber, if there is no clearance then the master cylinder piston gets held in a bit thus the little hole that allows fluid from the reservoir into the master cylinder chamber is blocked off/restricted. Hence the low volume/velocity of fluid arriving at the bleed nipple meaning any air in the system wouldn

How about getting a kids bicycle inner tube etc, fold it in half so the valve is at the end, feed some string/cord threw the pipe to pull the inner tube in to the pipe, then inflate it to try and pop out the dent. Or you could try some of the inflatable ladies

So excepting mike31270 are you all members of the BTSC - the Big Thick Sock Club?

I have been looking at boots and I am leaning towards Novogar Trials boots. Anyway I am a UK8/EU42 size (in steel toecap boots - I don