Gas Gas

Hi One of our TXT 50 boys threw its chain yesterday and annoyingly wrapped itself around the front sprocket twice.Since this catastrophie 1st gear is quite musical and jumpy. Have pulled motor from frame and have started to strip gearbox down, fault seems to only be in first when you turn the sprocket, big notch followed by a lot of slack. Thinking possible stripped tooth. Anyway wondering if anybody can point me towards any parts manuals, workshop manuals etc. Regards Simon

Hi to everyone out there,my GG 280 pro 05 has got play on the swingarm bearings,does anybody know the size of the bearings.I know you can buy the linkege bearings off ebay but i dont know if the swingarm bearings are in the kit.As i've just put linkege bearings & seals in just be for xmas i was hoping some one might know the sizes so i can go to my local bearing outlet & buy some. THANKS.

Anyone know the size? Mine is leeking. I can measure it in the weekend but if somebody knows i can ride this weekend

Hi there, had several trials biked in the past mostly 4t, but recently bought gas gas 2006 non runner no spark, checked basics kill switch, plug, did test wiring non appeared broken, looked at fly wheel, elongated groove in it, should there be anything in the groove to create spark ?? I have replaced rectifier not sure how to check ducati coil cdi, Thanks in advance,,,

Does anybody know if the rear wheel from a 1993 Contact would fit an EC 3000 2001 with Marzochi forks ( not upside down ones). Cheers.

Rebuillt my sons 2000 TXT 280 top end and just need to torque down the head and barrel can any one give the correct values . I can't remeber were but I am sure I read 18 lbs for the head but that sounds a lot for a 6 mm bolt in to ally. Thanks for any help you can give.

Is anyone able to tell me the thread size and switching temps on a 2013 onwards fan switch? Also, is it normally open or normally closed> I'm fairly certain they are interchangable with 2011onwards Sherco switched but need to confirm. Thanks Ray

hi , i have trouble starting my bike after over heating , it is very easy to kick over, the compression is about 50 psi, does anyone know what the compression should be ??

Hi I recently rebuilt a 07 gas gas 280, i had to replace the selector forks which were bent plus one gear and the kickstart ideal gear. Now the 4 gear is noisy compared to any of the others and gear selction between 4th and 5th up and down is very difficult. I,m gonna strip it down again but is there anything you would suggest i look at closly. Cheer,s Daz

hi all recently my bars have had the feeling of being a bit low down,whether lack of riding or older age or riding my mtb more, what difference do bar risers make in the handling etc thanks

Hi, looking for clutch friction plates for my gasgas txt 320 on a 1997 age bike or atleased i think it's a 1997 320 according to the frame id...any ideas as to where i can get some....thanks

Just wondered if anybody has done this job , not bothered about having a go just wondered how much you take out ,ie just back to junctions etc rear light cable and then fit kill switch etc cheers colin

Hello just bough a 2001 280 gasser it is being a pig idleing I need stock air and fuel screw settings HELP thanks

i was just wondering what jets my 1997 gasgas jtx 270 running a 26mm carb should have because i believe its running rich ? thank you

Fan seems to be kicking in a bit more often than I remember on my bike (been a few years). Would this be a sign of a head gasket on the way out? Not boiling or emptying the rad, but the inside of the rad cap looks a bit dirty.

I've was having trouble with my clutch when going very slow/stopped with the clutch disengaged or slightly dragging. Often, the point where it is slipping and engaging will be abrupt, not smooth. I was reading the sticky in the Beta forum about improving the clutch and know about the clutch basket filing method used for enduro and mx bikes. GG has a steel basket and I noticed very subtle grooves worn in the basket. The pull is as light as new and thickness is within specs. The clutch plate tabs were a bit rough, which I suppose is how they come from the factory. I did a very light filing on the basket and a super light filing on the plate tabs and the clutch abruptness we…

Bonjour.quand j'enclenche la première le selecteur ne remonte pas.si je mets la deuxième c'est ok . merci de votre aide

I broke one of the rockers in the shock linkage on my '07 300. The US importer is out of them, and won't have any for at least a month. I can't stand the idea of being off the bike until the snow flies; does anyone have a set for sale? I'm after #37, part number BT280014005CT, in the picture: Thanks in advance for any help, Forrest

Apart from the usual pit falls of buying from ebay, at present a 2001 Ti (Team Issue) is being advertise fairly local to me and within my budget (c

Is 1600 a fair price to pay had a test ride and it was bang on and it is in nice enough shape Also are they any good anything to watch out for Any thing I should be aware of specific to gas gas or the 09 125 Thanks