Bultaco

does any know the code/numbers for a set of taper roller bearings as i dont want to pay bultaco uk prices when i can get them cheaper in a local bearing shop

Has anyone purchased one of these, if so did it fit allright, holes align etc. http://www.todotrial.com/ttshop/especiales-clasicas.htm# They appear to offer more width of coverage/protection than the std shield is this so. I also seem to recall an aftermarket shield that was turned or curved round at the sides, does anyone know if they are still available.

Hi guys When I received my Bultaco the tank was very worn, needed spraying. We sprayed it and everything was ok, until the petrol vapour literally destroyed the paint work and stripped the stickers we had on it. I understand that this is a common problem. Does anyone have any idea of a cure? Regards, Kelvin

I've stripped my M159 forks down and they have upside-down U-shaped spacers at the bottom of the springs, these spacers do not appear in either my Haynes or Clymer manuals. They are shaped like a capital U with a flare at the ends. Are they required or are they a mod' that has been completed by a previous owner in an attempt to pre-load the spring? Any ideas? I've got new springs, newly re-chromed stanchions (Philpotts in Luton) and new fork seals, so I'm not expecting them to have anything other than a "standard" feel initially, I can mess with the oil weight etc later. The general condition of the internals appears to be fine with no obviously excessive wear that mig…

How do you know if the front fork nuts are working,What is the best way to clean them. Thanking you in advance, Hightown

Does anyone have details of the modification to the head steady on a 199A (blue 350 325cc) What is required and what are the benefits

Hey folk's.... Here's some links to my BULTACO SHERPA 199A that I just restored for riding purposes. I think it turned out FANTASTIC, not a museum piece, just a real classy rider !!! Happy Trials until next time...

hello all can anybody tell me where i can get a new seal for the rear brake hub? allao should the front hub have one? my bike is a sherpa 199A 350T

Hi, I am slowly progressing with my M80 rebuild and I am splitting cranks to replace gearbox shortly. I am considering having the crank rebuilt with new bearings but most kits include a new conrod. This adds a lot to the cost when budget is limited! Is it feasable to rebuild using the original con rod with new bearings or is there a good reason for replacing everything? Also, can any one recommend a good engine guy in Newcastle/Durham area to carry out the rebuild? Cheers, Myson

Can anyone tell me the chain size (520 or 428) and fork travel for an M85 (1971 Alpina)? Thanks

hi all im unsure witch to get rack or trailer im going down cornwall next year with my bult would a bike rack be ok all that way or would i be beter off with a trailer? thing is my wife will be driving as i dont not sayin she cant drive ??????? ah ah but im just thinking with a trailer might be abit scary

hi guys whats the best way to ajust my clutch on my 350 199A i have a work shop manual it says bottom the clutch ajust screw and undo 3/4 and then tjghten the locking nut is that ok? cant do anything yet till i put the wheels on just got sum off ebay so when ive got them on and put the chain on then i can try the clutch hoping its just a littel tinker and not new clutch plats but if i need new plats then she will have them allso dose anyone know were i can get a stronger headsteady ive got new one on from bultaco uk i know sum have a blob off weld in the middel but ive seen a better metherd on a bike on here to bits off tube with flat ends and it looks like it strong just…

I've got wheel alignment problems with my Model 159, even after straightening the bent swing arm and triple clamp. I've measured and drawn up the swing arm and cast aluminum rear engine mount and it sure looks like the engine case center is supposed to be on the centerline of the bike with the swing arm centered on it too. Yet with good sprocket alignment (fresh sprockets too) to get the rear wheel aligned on the front wheel the rim has to be pulled over towards the sprocket to the point where I've got serious concerns about the amount of thread engagement between the spokes and nipples on the right side of the wheel. Perhaps the new Buchanan spoke set is off, with the…

hi all has anybody had the clutch case upgrad by billet if so dose it make a big diffrance its

Hi, wondering if anyone can help, i am thinking of fitting a tow bar on my vehicle for a bike rack but need to know the wieght of a 198A Bully, i thought about 140kg??????????????????

hi everyone im new on hear i had a bultaco many years ago when i was at shcool and ever since ive wanted anougher one so ive just got meself a sherpa 350 befor i stript it down it was runing ok started first kick now ive put it back together it wont start checked the usual plug got spark i dont think fuel is geting throw i took the plug out and it was dry can anybody help me please

Hi all, I'm interested in buying a Bultaco and was wondering if there is a model year or size that I should stay away from because of mechanical or ..... problems? I understand that they turn like a dream, just what I need where we compete in the Sierra Nevada's (Lake Tahoe area). Thanks for your time. john

hi guys im asking this question on behalf of a mate, he has a bultaco 250 and wants to know how much gear oil it should have, thanks for any help, Nick.

Hey, can someone send me a link to the movieclip of a white bultaco (puma?) that is ridden in spain by a very good rider. i have seen it once but i cant find it anymore thanks a lot! best regards bob

hi all can anybody tell me how to get a good earth? ive took the coil off and sanded the frame down to metal ive put coil back on its a beter spark but think it should be beter my new coil should be hear tomorrow from bultaco uk the old one is rusty and the bolts would it make diffrance with the new coil and bolts? allso would a front wheel off a purstang m8 fit my 199A