Bultaco

hi can anybody help ive just finished my 199A just put a new clutch plates in barnet ones im trying to set it but kick starts turning over but sliping but just noticed one of the spring cups had pulled throw it had the metel ones in i thought it needed new plates but turned out the was no throw out ball so put one in i know its somthing supid im not doing gonner wait till new cups come and try again but your help might put some light on the matter i had it runing and she pulls ok just needs the carb settin i put the right jets in as it was a new carb from spain but didnt come with the right jets

Hi My M159 is all restored with new seals, bearings etc, etc. The only moving parts not renewed are the piston/rings/bores (loads of compression and fine in my opinion) and the swing arm bushes (not a problem). Apart from that its all new. I've fitted electrex ignition which is timed correctly for this model I believe (2.9mm BTDC) checked on a strobe and it starts on choke very easily. Everything is very smooth and lovely, BUT, in order for it to tick over correctly once warmed up it has to have the mixture screw wound all the way in! If I try backing it out at all (1.5 turns out is standard) it coughs and backfires even at 1/8th turn out from fully seated it starts to…

Dear All, I'm now at the stage of putting my Frontera back together. I've got one of the Electrex electronic units and am too embarassed to ring them yet again as to how to set up the timing! I have their info sheet but I still can't work it out. The Bultaco manual says static timing should be 2.4-2.6 mm BTDC, that's static timing. The Electrex unit automatically advances above 4,000 rpm. The Electrex sheet says that 2.4mm BTDC equates to 22:30' degrees BTDC on the flywheel and suggests you use a strobe to set the engine (i.e. when running) to this. So engine running set to 2.4 mm BTDC, engine static 2.4mm BTDC. SO where's teh advance gone? DO they mean that you run the…

Hi all, I wonder if you could help me with my 2 questions below... 1) I am currently finishing the full restoration of a model 150 Sherpa T 250 and got the engine running today after installing the (new style) electronic ignition from Dave at Bultaco UK. The bike starts, idles, revs and runs really nicely - the problem is that when i blip the throttle the revs don't drop back to idle as quickly as i would expect. After each blip, the revs drop gradually, slowly settling back to normal idle - it may only take 1-2 seconds, but it doesn't seem quite right to me. - I have had the engine fully re-built by the guys at Bultaco UK, so it should all be sound - The throttle se…

hello all can anybody tell me whats the best way to seal the holes were the greas nipels go the only reason im sealing them is because ive put the rolling bush kit in ive tryd clear silicon and it just keeps coming out when its dry is there somthing else what would work?

At the recent Telford show there was a Bultaco trials bike with a chromed frame standing next to a Model 10 near to Dave Renham's stand. The front half of the frame looked std Bult but the rear was quite different, do you know the make of frame or reason for its modification.

ok i bought a sherpa off ebay a while ago with the view to restore and ride, i've done 3 trials on it and want to get a few things done before the sammy miller rounds start. first off forks, im going to be riding the harder routes on this bike so with that in mind, can anyone recomend springs, oil and amount? also has anyone altered the fork angle? i've already got a mikuni vm26 in the garage and was hoping to use it but havnt got a clue what the jetting would be, anyone had any experience with these. Also thinking about skimming a little off the fly wheel to improve response, but worried i'll sacrefice grip. Going to lower and replace the footrests aswell. if anyone can …

Hi I need a new L/H Crank Case and Magneto Casing, will any other model in the range work? The old ones have been battered by a chain snapping. Will the 158 fit? Do I have to do anything to make any other case in the range fit? I don't want to have to start cutting it about and welding etc. Just trying to broaden my options. Cheers Mick

Hi all, I have a 340 Bultaco, I bought it off Roy "Ago" Wilson some years back, although I have ridden it a few times it is a bit rough in places and I'm currently considering a general direction for a refurb ( i.e. do up as is or continue the development)for another go at riding it. At the time of purchase it was already in a fairly modified state i.e. having been vesty-ised to some extent at the rear end, according to Roy this could have been carried out by Chris Milner. I managed to speak to Chris at a trial a few years ago and he could not confirm if it was his work or not, I have also spoken to Dave Renham who confirmed that it was supplied new to Dave Thorpe, I hav…

. A quickie off the www from Claudio...! Charles in Charge. Cheers Chaps. Motosinge83.

I would like to contact Wayne Weedon to ask him a question about Bultaco brakes that he would be most qualified to answer. It does not appear that he is active on this site anymore. Does anyone have contact information for Wayne? Thank you. Rich Lee Pennsylvania, USA

could anyboy tell me were the over flow tube gose on the chutch case? ive got it tuck inbeween the finns at the moment but wont it melt with the heat or is there a fitting that clips on the finns so the tube can go throw?

Hi - My first (last) posting concerned head steadies; continuing in a similar engine bracketry vein, can one of you knowledgeable Bully fans tell me what the bracket on the left fits? This places the swing-arm pivot about 1/2" closer to a line through the engine mounting-bolt hole centres than the Sherpa 340 bracket on the right (which has the same hole spacing as the older-style alloy bracket 159.10-064). This the second time I've bought one of the these unidentified brackets (sight unseen, of course) and was assured by the sellers in each case that it was removed from a Sherpa; I had a feeling they were Pursang, but the only MX one I have is different again, as …

Hi all, I was wondering if someone could give me a colour/paint reference for the blue and silver used on the aluminium 'homerlite' tanks on a 74/75 Sherpa T 250 (model 150)? Please see pic attached for reference. I have a compressor/paint gun setup, or can use spray cans if there is a good match anyone can suggest. Any suggestions welcome. Thanks in advance. Cheers, Max

hi all dose anybody know were i can get a stronger hesdsteady?

I'd like to hear some evaluations from those that have used them. It seems to me that a 325 has plenty of power, but I wonder if an ignition with an advance curve would noticeably widen the power band by letting the engine rev higher. That would likely rerduce the need for shifting in a section.

Hi, I have just split the cranks on my M80 engine and have found it has 3 main bearings. I was sure that it was only later models that had this feature. I also want to remove the two gearbox bearings that are located in blind holes, what is the best/easiest method? Cheers, Myson

2 and bit sherpas

hi, could anyone please tell me the blue color for a bultaco 175 221, grabber blue or ral 5015.

I have recently dragged my last remaining Bultaco from the back of the shed where it has spent the last couple of years in disgrace. A few years back I decided to try sidecar trials, so got hold of a chair which was once fitted to a '74 model 125. I purchased a matching bike which was running absolutely perfectly, but had trashed lower frame rails and other frame damage so was ideal for the project. Mods duly done, the bike was reassembled, but wouldn't start. Crank seals I thought, so I whipped a new set in. Still no joy. To cut a long story short I stripped and reassembled the bike (I didn't split the cases though, or lift the barrel) till I was sick of the sight …