Montesa

anybody out there with a kehin carb on a cota 315? How do they perform? what jetting do you need?

hello all ive tried the internet but to no avail , where can I get a ignition coil for a 1999 montesa 315r many thanks stan1

Just arrived : Another part of the jigsaw. Think that these will also fit 249 as well.

The rear shock on my 309 is leaking badly are they repairable or common with any other models,a serviceable used one would help me out !!!! Thanks in advance Chas

Hi I lost one of the side seat/tank body mount screws ( the ones with the large 20mm approx pan head ) . I have some spares but they are too short for the tank/seat that I am using. Can anyone suggest a supplier - or are they commonly available parts ... maybe I am not searching for the correct term.

Hi, I'm just going to change the fluids on my 349 prior to putting the new carb on.I'm guessing the large screw on the bottom of the left hand side case is the drain for the the transmission oil and the fill plug is on the top. I presume the plastic screw under the engine is the drain for the gearbox oil with filler above. So far about 1/2 teaspoon of water out of the transmission and a tablespoon of oil from the gearbox. Could someone confirm this and let me know correct lubricants and quantities please. Thanks for looking. Neil

Cota 348. After rebuildinbg the engine the gears do not shift smoothly, so the engine is in pieces again. I want to set the end play on the drive, input shafts and the shifter shaft. Can anyone tell me what the end play tollerance is and if anyone has any advice then please share.

I urgently need a stator for a 99 315r, Im on holidays and spark has failed. Replaced coil and cdi, but still no luck. Any help greatly appreciated /

I am trying to find out what is the spoke off set to the rear of an 81 248 cota. I have sent the wheels off my 248 to be rebuilt, before sending off to the wheel builder I decided to strip them myself so I could polish the rims and hubs. This has proved to be a bit of a possible oversight as the first question I am asked is do I know what the offset is, he has looked a various sites with out success. Any help would be most helpful.

Are there any secrets to removing the chain tensioner pivot bolt on a 2018 300 4rt? So far I have tried penetrating oil, heat and a few heat cycles. Does a steel bolt thread right into an aluminium pivot?

Hi all, is there anybody that provides an alloy tank for the Cota 21M that will sit under the original tank / seat unit with the old tank base cut away? Or can anyone suggest a company that might make one.

Just purchased my first Cota 314r and wondered if any body new if a light kit could be fitted as the bultaco i was riding was used on the rd at dusk to get me back to car and trailer. If so any advice would be welcome, ie wiring loom, where to connect and light kit. Thanks all

Has anyone tried the 223cc mod on a Cota 200? Fit a 247 piston in a 200 barrel = 223cc.

Hi All, my best friend has just brought a Cota and has asked me to help him put it on the road. Now I’m totally new to classic trials, I rode Motocross in the 90’s and plastic rockets for 20 years plus. so with the above in mind, any advice from you guys with regards to Cota’s Would be greatly appreciated. i will be looking returning it to the road. Is there any mods, ignition, lighting etc that you could advise me on. all help greatly appreciated

Hello, I am new on this forum, I start restoration project on my Cota 123 from 1972. I know the paint is a kind of dove gray or silver but cannot fond more details. Does anyone got more information like maybe a color code? how did you guys did to get the right color?

hey, does enyone has the parts nr of the rear mudgard of a 2007 4rt? regards bob

Are the the threads left or right handed on the flywheel and sprocket?

Hi All, Could anyone assist me in how to remove the selector arm? Been banging my head..... Need to remove gear directly behind, apologies if it is a dumb question, but never done one before! Cheers, Mark

Hi, does anyone know if there are metal tanks available to fit under the orignial glass fibre seat & tank unit? I know there are treatments available to prevent ethanol 'eating' the glass fibre but a metal tank would be preferable.

Im helping a friend with a Cota 25 vintage kids bike, does anyone know oil quantities for gearbox and primary drive? thanks!