Skip to content
View in the app

A better way to browse. Learn more.

Trials Central

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

thall1

Members
  • Joined

  • Last visited

Everything posted by thall1

  1. thall1 replied to thall1's topic in Beta
    In answer to my question.. yes the pump does need to come out to lift the barrel as the water pump gear and shaft won’t allow the chain to come out… impeller was just very very tight on the shaft. Had to keep pulling with wide pliers… not nice but got it off in the end!
  2. thall1 replied to thall1's topic in Beta
    I’ll answer my own post for future reference! the trick is to turn the bearing retainer clip so one end is above the bearing journal.. place a thin wedge ( I used a 6” rule) between the end of the retaining ring and the face of the head to stop the retaining ring from spinning… then use a good pair of pointed pliers to carefully prize/ lift the retaining ring clear of the bearing. Once it’s off you can remove to camshaft side bearing, tilt the shaft and remove the inner bearing then drop the cam down to lift the chain clear. Note: you will need to remove the water pump and the water pump shaft from the water pump drive gear and then slide the water pump gear out to allow the chain to drop down below the head and barrel and allow the head/ cylinder to be lifted clear. You need to do this prior to lifting the cam out as the cam train holds the water pump gear solid to allow the shaft to be undone. There is a special tool to undo the water pump shaft… I didn’t have one so used a stud extractor tool. It’s pretty tight so be careful!!
  3. thall1 posted a topic in Beta
    Starting to strip my 2013 4t.. gearbox issues…. Can’t get enough slack on the chain to remove the cam shaft! tensioner is removed… manual says just to lift the chain off the gears and remove the cam but I can’t get enough slack. also the retaining ring for the cam shaft bearing is slightly too long to come free of the retaining groove to allow the bearing to slide off?!… Ive even tried removing the guides from the block but they won’t come out either at this stage I must be missing something in the manual but I can’t think what?
  4. thall1 replied to thall1's topic in Beta
    I did wonder that and that was going to be my next question!… I’m just working through the manual in the order it shows atm. funnily enough we went the other way.. 4RT to beta 4t!
  5. thall1 posted a topic in Beta
    Starting to strip my 2013 4t.. gearbox issues…. Cant select gears, lat month I snapped the quadrant off the gear change shaft.. I repaired that and made a new pivot slide for the change fork as it was really sloppy… gear change was brilliant after… until I dropped the bike onto rocks now I can sometimes select either 1st or 2nd but nothing else… the gear shift drum behind the clutch basket isn’t moving so something is amiss in the gearbox.. started stripping the engine today and first snag is I can’t pull the plastic water pump impellor off its shaft!.. circlip is removed, there’s a little bit of movement between the shaft and the plastic impeller but it’s stuck fast!… tried pulling with all I can whilst gripping with a pair of pliers and it’s not moving… any thoughts?… thought I’d get further than this before I hit a snag!
  6. Not that I know of.. when I had my Montesa I fitted dimpled clutch plates… they did make it a bit less switch like which is the opposite of what I’m looking for…!
  7. My 2013 clutch has always felt a bit too soft.... there's no positive 'spring' at the bite point....we've got a 2014 4T as well and that's totally different.... almost too 'switch' like...not quite as bad as some Montesa 4RT but not far off... I've fitted new clutch springs, slave & master cylinder piston kits. The clutch pack is well within the limit. Its almost like it needs slightly stiffer springs... cant find any though... If I put a thin washer under the head of the bolts on the clutch pack would this make the clutch a bit stiffer and a bit more positive?
  8. ive drilled out the original pin and made a new one to better suit the dimensions on the gear change shaft....all fitted and seems to index the gears better. time will tell!
  9. I’ve got two flats on the guide pin… I’m assuming this is wear?… there’s quite a bit of free play in the gear change shaft linkage which appears to limit the movement for selecting 1st and 4th. Neutral to 2nd and into 3rd seems ok… think I might turn up a new pin with a closer fit.
  10. I’m not sure if there is. ‘Fail safe in the box … a weld wouldn’t be good for that… anyway mines all welded now, I’ll try and get some gaskets tomorrow and hopefully I’ll be good to go!
  11. All sorted now… I just refitted the clutch plates and a quick burst with the gun and it’s all off. anyone rewelded the shaft before?
  12. Weld has broken on the gear change shaft. How do I stop the nut and inner clutch basket from spinning when I put the impact gun on it?
  13. ok ill try that
  14. thanks guys!... I'll take a look later in the week....any tips for holding the clutch basket while I undo the nut without the correct holding tool??... I remember breaking a clutch basket pillar on a Montesa a few years ago trying to loosen the nut...not cheap so would prefer to avoid that again!
  15. Hi guys, hoping someone can advise.....2013 4t, gear lever shaft has lost its normal 'stops' both up & down the gears. I can still select gears but the lever & shaft continue to move in both directions. It doesnt stop in its usual 'detent' positions and wont return to its 'neutral' position after changing gear...Its internal so its an engine out job but can I get to the gear selector mechanism or the gearbox itself without dismantling the engine first?...any thoughts as to the problem?
  16. Hi, i need to make a new front wheel inner spindle spacer, does anyone know the length it should be... ?
  17. thall1 replied to Corker's topic in Beta
    As totty79 said check the visible items that he’s listed above but also unless he has receipts, then also factor in brakes pads front and rear, Caliper piston sets front and rear, rear brake master cylinder and clutch and front brake master cylinder.... I haven't a bike yet that I haven’t that I had to change them in the first year
  18. thall1 replied to Corker's topic in Beta
    Give beta Uk a call with the VIN number
  19. Bvm moto, GasGas Uk..
  20. I know the feeling but I think you need to fix it first, if nothing else to be able to get a good price for it...
  21. No worries!... it’s going to be a tricky one to sort out...a second bike to rob parts from would be very useful!
  22. I did try all the swapping all the above parts when mine played up, fuel tank, injector, ecu, loom, temp sensor and a few times over but chasing an intermittent fault is tricky...
  23. I think you need to try and borrow one first.. it’s a lot to pay out for if it’s not the issue. If the bike came from a dealer have a chat with them and see if they can help?
  24. Mine was a 2006/7 bike but I have heard of newer bikes with ecu faults .. I think a new ecu is around £400... I think I paid about £250 for the one that was fitted on mine to test. The ecu is part of the throttle body. It’s all a bit tight but it does come out.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.