Jump to content

ar22

Members
  • Posts

    104
  • Joined

  • Last visited

Everything posted by ar22
 
 
  1. We rode in the scott trial last week and one of our biggest fears was a front puncture as they are very time consuming and a general massive pain to sort by yourself half way up a moor. We did use a heavy duty tube with slime in it and did avoid punctures but you will never know how close you actually got to getting one. I have since noticed that Nitromousse list a "plushie" for a Michelin x11 and Dunlop front tyre that gives 6 to 8 psi These seem ideal for the Scott/SSDT I know that a mousses historically were generally regarded as too hard and had little feel to them but they seem to have come on technically (so they all claim) in recent times. Now I assume because of the popularity of hard enduros they offer the much softer options that give trials like pressures. They also list one to fit the tubeless rear, not too sure how that works but am more interested in the front at the minute. Has anyone tried one of these from Nitromouse and if so what is the feed back ? Has anyone tried a different brand that works well ? https://www.nitromousse.com/ many thanks
  2. sorry should have said they are Showa
  3. my 315 has an annoying crack/banging noise on full extension fork seals are good and checking the oil levels they seem fine as per the manual, oil was recently changed. The manual does mention in the right fork section a "stopper rubber" I don't see it in any of the pictures or the parts diagram, any ideas ? I also see that the left fork has a "rebound spring", this could be adding to my noises, do these generally give any bother ? I see it in the parts book but unless I am wrong its doesnt list it with a part number. before a full striping I would like parts at hand or at least located as I dont want the bike off the road for long and although annoying its perfectly ridable. thanks
  4. 07 sherco 125 shock has decided to let the oil out its the original and it seems it may be easier to buy a used shock than trying to get this rebuilt what other year of sherco shock fits into an 07 bike ? thanks
  5. ar22

    07 125 pig to start

    had thought that, but took head off and filled it with petrol, rings sealed it well with no leak through. better do a compression test
  6. We have an 07 125 Sherco it has always been a bit problomatic to start from cold but we always put that down to the fuel tap not turning off properly and it flooding the engine over time, this has has now been fixed. The bike is hard to start cold but when it goes it runs perfectly but if you stop it hot its a pig to get going again. had barrel off and all is good in there, tested ring sealing and all seems well. carb is clean plug changed thinking it may be coil or stator, do these give bother and if so is there any way of testing them ? any other ideas ?? thanks
  7. Beta manufactured the motocross engines for Ktm 50 and 65 from 2004 to 2008 The Beta rev 80 engine is the 65 engine with a different barrel. The 50cc Beta trials also used the same auto engine Beta and KTM have had strong links engine wise and led to believe the newer KTM engines have a lot of Beta influence if not some manufacturing.
  8. she has the flywheel weight already it just wanted to run on so much, it was all clutch and brakes that made it hard work 10t and new slow throttle on tonight and she will be a different bike
  9. moved my son from a 125 to a used 300 evo out on sunday for the first time and she was lovely and he loved it but a handful searched this site for how to calm her down a bit head insert, slow action throttle, 10t front sprocket all decided upon just checked before ordering anything and she has a 13t front sprocket ! (41r) no wonder she was such a handful and why all sections were in 1st gear moral: always check the basics
  10. after a few nights doing the search with google and "trials central..............." I have found more threads covering all my topics and other things I only thought about than I can believe. so apologies to those who have looked at them and said "that has been asked 20 times before" and rolled their eyes I was actually a bit embarrassed as the neutral selection issue it seems has been talked about to death thanks, its a great site full of great info (if you can find it)
  11. thanks for all the replies I read every post in "the clutch fix" with great interest and realise a lot are having dragging issues also causing neutral issues too. But our clutch did seem ok when cold, its nice and light and just slicked into first without even a jolt forward. I will take it out and give it a good clean anyway but it seems its a Beta thing and we may have to just live with it. I will also reduce the oil mix as recommended, better just check my 315 Montesa can run so low as I wont be making 2 mixes I would be interested in this though, if anyone has the answer it was only my sons first day out on the 300 after moving from a 125 Sherco, seemed a nice running, easy starting bike with obviously plenty of power, any set up hints or mods that make it better would be appreciated, (I am not very good with the search function on this forum) thanks again
  12. cheers I think I will drop to 60:1 this is really hard to get neutral, almost impossible
  13. had the 2012 Evo 300 out today for the first time. couple of minor issues the exhaust was spitting oily mess from the mid joint, I had the exhaust off last week and had fitted 2 new o rings. I will remove it again check the o rings are intact but refit with sealant to ensure a good seal. will silicon do the trick or is there some else I should get ? I ran it at 50:1 as I had it mixed, I think I better reduce the oil a bit as per the book. and repack the silencer. clutch seems great, no dragging even when cold etc but while the bike is running it is very hard to find neutral from 1st, its a bit easier from 2nd any ideas ? thanks
  14. had the 315 out today and can report a vastly improved front brake the lever has much more feel, before it was very wooden it not as sharp as our Beta evo brake but still very acceptable. I am still using the standard caliper, I suppose if I want more power I will have to fit a 4 pot but I doubt I will do that, unless I get offered one cheap. thanks
  15. ar22

    Beta Bolt Kits?

    I just bought them on ebay, various lengths available so no cutting required and they are very cheap
  16. 5mm stainless insert made much neater now
  17. thanks just found and ordered a 25cm length of 5mm OD stainless tube for £3.45 think a bit of it should do the trick combined with a short breather tube and one way valve will tidy the fuel cap up nicely
  18. does any one know of a straight adaptor to replace the 90 degree elbow on a 2012 evo fuel cap would like to fit a short breather pipe with vent on top I have seen the Racing cap but its £50
  19. I didnt know about it either, having read it it certainly has lots of hints on how to look after a Beta even if not doing the SSDT https://www.ssdt.org/docman/2017-scottish-six-days-trial/238-2017-scottish-six-days-trial-beta-preparation-guide/file
  20. yes my 1984 ty250 had zerks too, really handy although if you were a bit over zealous with the grease gun the seals would pop out so not so good.
  21. giving the Beta Evo linkage bearings a lube and a couple of new ones for years i have been using good quality grease from a tub and using the end of my finger to push it in as I assume most do although I turn the needle bearings, I feel that the bearing never really gets filled with grease as well as it could does anyone recommend a good brand/type of spray grease that goes on in liquid form, therefore running right into the bearing rollers and then when left it thickens. there are so many types of grease and almost all mention bearings, or maybe all of them would do ? I considered chain lube but maybe its too tacky ? thanks
  22. my bearing only has a very bit of movement in it, so ok to ride for a weekend or two so dont want to take the old one out and find the new bearing delayed etc, I just want it for the shelf to fit at my convenience. I know the bearing is a GE12 but has another letter too as the "standard" GE12E is 7mm wide, the Beta needs a 10.4mm (ish) wide body and therefore a bit of an odd bod I might end up just getting it from Splat but do like to buy from a few local bearing shops too and I just go in with the exact bearing code and not waste too much of their time searching for for what I know is an odd size.
  23. any idea of the bearing number so I can order one from my local bearing shop 2012 evo 300
  24. I received my Ajp (large) master cylinder and a set of Galfer pads The master cylinder was a direct replacement for the Gremica, the brake hose fitted straight on in a few minutes and bled up easily. I haven't ridden the bike yet but the lever had much more feel to it, before it was very wooden and pushing it up and down the garage it now seems much sharper. will report back when I get a good run on it and bed the new pads in.
 
×
  • Create New...