Gas Gas

I am wondering how much sag is recommended for the front forks on a TXT200? If I understand right sag should be set at about 1/3 of travel. I'm not sure what the total travel on my bike is. Anyone know these measurements?

I wonder if there are anyone here who has done more to their TXT 70/80 than just the obvious mods, for example as described on the US GasGas homepage. I have taken the engine apart, cleaned it, rebuilt it with new bearings, seals and so on. I have tried the mods to the standard Dellorto carb (raising the needle and grinding a 2mm nothch in the thottle) and I have tried taping off various parts of the airbox intake. And it works OK even if it has to be leaned out under certain conditions. Problem is, when the rider (my son) gets more experienced, he need a bit more power and crisper power delivery. I have been thinking of boring out the cylinder to the class limit (80 c…

Hi to all. I need a 2.0mm clutch plate for my sons 2003 txt50. Gasgas uk have them on back-order from the factory but have no indication of a delivery date ~ try explaining that to a 7 year old! Any help greatly appreciated before I am 'nagged-to-death' :-)

I see the seat kit for the 2011 gas gas txt but it says it is only for the 2011 and newer. Has anyone tried to adapt it to the older model? I have a 2009 and would like it. I know there is the jitsie one but it is lower and seems flimsier.

hi all looking for some advice on my boys gas gas 80 2003 model. The problem i got is there doenst seem to any power in second gear if your on the flat its great but come to a hill and it just bogs down. Ive cleaned the carb over and over again ive changed the mixture to your advice but it just doesnt seem to be working. So my next job is cleaning the exhaust and re packing as its gone really noisey will this make any difference. So if anyone knows please help thanks steve.

does anybody have any better wiring diagrams than what is featured in the manual or even sum instructions would be amazing, its an 05 125cc. thanks chris

My son has a txt 70 2002. It is becoming difficult to shift the bike into neutral when the it is stationary or when the engine has stalled. Any suggestions on why and what to do about it are welcome. thanks

Hello, Any ideas/tips/help/or previous knowledge??? Just sold my 2004 280 pro because i found the power was slightly to much, so now gone back to a 2003 250 pro... To be honest i think i find the 250 easier to ride (softer) but sometimes just need a little extra something.. I have a 280 flat slided carb sat around unused so have decided to try it on the 250 to give better bottom end to top end with out the full-on power the 280 brings. So i now have it fitted and it runs ok, feels a bit weak and doesnt tick over quite as smoothly as id like but lifting/dropping the needle may cure this!! So now for the question?? Does anybody no what jets to try to make the full po…

hi , i have trouble starting my bike after over heating , it is very easy to kick over, the compression is about 50 psi, does anyone know what the compression should be ??

Any others compatible? cheers Andrew

getting ready to order a spoke torque wrench, but wondering the size of the spokes? Thanks boys

Picked this up last weekend as a non-running project for $750. Been working on it for the last week and she's running good now. Below is what I've had to do to it so far, it's almost done and ready to ride. I'll be doing a full youtube video on the process when I'm done - channel name is 'MrTwoSmoke'.

Hi everyone Is there anybody who could assist me please I'm rebuilding a 1994 JT35 and where do I buy full gasket set and all the bearings for the frame and seals ????? regards Alex

Bonjour voilà mon amortisseur me semble pas trop en forme. 1.moto sur pied roues levée 55.5. Cm 2.roues au sol 51 cm 3.avec pilote 45.5 cm ressort 72.5. Vu mon pois j'aurais besoin d'u N 80.0 Ressort reserer à 15 mm. pas bon tout ça..avez vous une idée ???? Merci de votre aide.

Does anyone know the sizes of the bolts on the rear caliper? I need the bolt that holds the caliper onto the frame. It's siezed and before I drill it out I want to have the replacement bolt.

Hi does anyone know where I can get a new rear mudgaurd for a gasgas txt 2008. Thanks

Hi there, does anyone know who or were sell the carbon fibre cover that covers up all the rear silencer both sides? cant seem to find them. thanks

Hi guys I have a brake fluid leak from the swivel spigot were the feed pipe connects from the reservoir to the master cylinder on the rear brake , the spigot is a push fit into a rubber seal , this seal is leaking , has anyone replaced this seal , and who can supply one , I’m in uk . Bike is a 2005 gas gas pro 250 thanks for any help

I have just bought a txt pro 300 2006 and the Rad fan comes on after only a few minutes running, is this normal or do I have a problem ? Thanks in advance

Can anyone tell me what compression should be on 07 TXT Pro 300 ? Thanks Jim A