feetupfun

Why does it have to be silicone? What's wrong with aluminium? You could support it from the existing muffler if you make it light enough.

Yes inserts are available and they are made of aluminium and are intended to be welded into the barrell. There may be other places to get the inserts but I just bought one for my MAR from Keith Lynas in the US. There is a link to Keiths website on the fantastically informative OSSA site run by Mats Nyberg. They usually strip because the nut works loose and the threads rub together due to engine vibration. Prevention in the form of tie wiring the nut will prevent it happening again.

If you truly are selling because of lack of space, you will certainly regret doing it later on. I reckon keep at least one OSSA even if it means getting a bigger storage area or leaving it at someone else's place till you can fit it in. I'm with Big John on this. There is no way I would sell a twinshock trials bike that has some meaning to me. It would be like selling your family videos and photos. There is no way to put a price on those either. For the mercenary people though that are thinking along the money lines, remember that we are probably the only people sufficiently interested in our treasured twinshock bikes to restore and enjoy them. Once our generation is gone, there will be very little interest in them hence demand (and prices) will eventually drop.

The Scorpa SY250 motor eventually suffers from both shiny plates and grooves in the basket fingers. The shiny plates mean there is no way for the air to get in between the plates when the clamping pressure is released. Roughening the plates provides a path for the air. I successfully filed the fingers smooth on my TY250Z (which has the same motor as the Scorpa SY250). Baskets are very expensive so it is worth filing them a few times before replacement. It needs to be done very carefully to prevent bending the fingers and keeping the engagement surfaces on the fingers flat and square. From how you describe your riding style it sounds like once you fix your clutch it will stay good for a while. Have a look at what the top level riders do with their clutches when jumping up big obstacles from a standing start and you will see that they cop lots of hard use ie full throttle, peak RPM, drop clutch in third gear. I've heard that the clutch in your Scorpa SY250 shares a clutch with an early 1990s Yamaha YZ125 so it is designed for a bit of abuse.

Pumping the clutch lever does nothing but build arm muscles. Leaving the clutch lever pulled in when you are not riding it sags the clutch springs. To free the clutch, there are two easy options: Option 1 Without starting the motor, change into 6th gear, hold the clutch lever in and rock the bike. Option 2 (if you have the riding space available) Start the motor in neutral. When you are ready to go, push off with one leg and select first or second gear while it is still moving. Change up gears until you are in a high gear and then pull the clutch lever in and ride around a bit like that till it breaks free. You can fix the problem by: Roughening the steel clutch plates (bead blast or coarse abrasive paper both work fine) and removing any wear grooves from the fibre plate tangs against the basket fingers. Both fixes are temporary if you are hard on the clutch (probably the same as you've seen with MX bike clutches). What people have told you is right. It is a common problem with trials bikes. Most people don't bother to service their clutches because once the clutch is freed it works fine till next time.

DT175s from 1978 onwards have a different stud layout than the TY175. So some DT175 barrels are interchangable with TY175 barrels and some are not. The TY175 motor is based on the 1974 DT175A so the A, B C and D model DT175 barrels should fit. I know the question was about the TY125 but I've never worked on one of them. Why would you want to fit a DT barrel to a TY motor anyway? Is the DT barrel better in some way than a TY175 barrel?

Here are the basics for setting up forks of the twinshock era: Spring preload Fork spring preload should be set ideally to give static sag of 40% to 60% of travel with you standing on the bike pegs with no weight on the bars. It is adjusted by adding or removing spacers above the springs. TY175 standard has a tubular steel spacer about 70mm long. If you add too much preload, the springs will coil-bind (which limits travel and may kink the springs) Oil level Fork oil level should be approx 125mm from top of tubes with springs removed and forks fully bottomed. The resistance to bottoming can be increased by using a higher level of oil. Too much oil volume and you will limit the travel. Too little oil and the damping holes will be exposed to air at the top of the stroke. Oil viscosity Start with 15wt oil. Heavier oil will increase resistance to bottoming out on sudden impacts but will be of little benefit during sustained heavy braking (on a steep descent). Heavier oil also produces a more dead feeling front end which makes hopping the front harder work than it normally is on a twinshock bike. With a bike the age of your TY175, it is entirely possible that there have been modifications made which are causing your forks to feel weird. I have tried many modifications to TY175 forks (wide range of oil type, different springs, air caps, a great range of preload adjustment) over the years and finally ended up with them completely standard as being the best performance. The next change was to fit TY250 forks which made it just how I wanted it all along. If you are in doubt about what trials bike forks should feel like to ride with and even just to push down on, try someone elses similar bike for comparison. If still in doubt, compare what your forks look like disassembled with a set you know to be standard.

Brushing epoxy works perfectly. It is thin enough to get it to coat everywhere inside and it takes hours to set so you can leave the tank to drain out and only a thin coating remains. It sticks great to old fibreglass if you clean out the premix properly. I cleaned my tanks out with turps, then thinners, then acetone and left them to dry fully overnight before the epoxy. Choose a bright day so you can see inside easily to see that you have coated everything. I put plasticene where I dont want the epoxy to stick ie like the cap thread. Brushing epoxy protects the fibreglass from the ethanol that is in some car fuels too. You should be able to buy it from boat shops and model aircraft shops. It cost me $40 for 500ml which is enough to do an M138 Alpina and an M49 Sherpa. If you do them all with the one mix, that would probably be enough to do three tanks. Only about 75ml stays inside the tank but you need to put about 250ml inside to start with to make sure everything gets coated.

The steering angle on the standard Ty175 is not as steep as most bikes from the same era. If you raise the rear with stiffer springs, more preload or longer shockies, the steering angle improves towards the ideal. If you then slide the forks down in the clamps, the steering angle will move back towards standard, but will improve the ground clearance. A negative with sliding the forks lower is that it makes the front end even more flexy in rocks. Going the other way (lowering the front), there is a limit created by the clearance between the front mudguard and the lower fork clamp. This limit is just a bit past when 20mm of tube protrudes above the top clamp. If you are serious about improving the front end, consider fitting the forks and clamps from a Ty250 twinshock. It is a bolt in job and improves the front end quite a bit, especially if you ride big obstacles or are over 80kg. In that case, the tubes are fitted flush with the top clamp and this puts the bike height at the front the same as with the TY175 forks with 20mm protruding. With either set of forks, you really need to set it up to suit yourself. I have found that it is far more important on TYs to get the oil level set exactly right than what oil weight I use. They have seriously poor damping if the level is even slightly too low. I find 10, 15 and 20 wt all work OK with the correct level.

JayLael You knew someone was going to ask if you would post a picture of the modified KT, didn't you? Please do if you can. Thanks David

The leverage ratio on twinshock type suspension never stays exactly the same throughout the travel. The mount locations on standard bikes are usually well chosen to minimise the variation in leverage ratio throughout the travel. When people modify only one mount location on a standard bike, the new arrangement can produce the desired increase in wheel travel but becomes less ideal as far as leverage variation is concerned. Laying down shockies by moving only the top mount forwards (or similarly by moving only the bottom mount forwards) usually causes the opposite of rising rate ie the leverage ratio on the shockies increases as the swingarm moves upwards.

Following on from the previous post about leverage, here is how to calculate how much you are changing the leverage if moving one or both of the mounting points or the compressed or extended length of the shockie or the length of the swingarm. First calculate the existing leverage ratio: Measure swingarm pivot to axle centre. (distance 1) At half travel position, measure from swingarm pivot centre to centre line of shockie at 90 degrees to shockie centreline. (distance 2) Divide distance 1 by distance 2. You should get a ratio of about 1.05 for a standard TY175 (Ratio 1) Now calculate the leverage ratio for the proposed changes: Mock up the proposed changes and do a similar set of measurements. If you move the top mount of standard length TY175 shockies to halfway down the plastic sidecover with no other changes, the leverage ratio will be something like 1.25 (Ratio 2) Now you can work out how much extra loading you will be applying to the shockies by the proposed changes. Divide Ratio 2 by ratio 1. (1.25 divided by 1.05 = 1.19) ie the new loading will be 119% of standard ie a 19% increase. Jay is telling you to make sure a suitable steering head angle is retained when you start fiddling around with the height of the rear of the bike (changing the height of the front or the rear of a bike changes the steering head angle). It is usually possible to achieve the ideal steering head angle when you do shockie mods without doing any mods to the front part of the frame.

You should expect about 30km/3 hours range gentle trail riding on a late 1990s trials bike with standard fuel tank in mountainous terrain.

I'm one of the people with a 250 MAR (MK II) fitted with a standard KT250 carby and it is still working very well. A riding buddy of mine has a Mk I MAR fitted with the standard Mikuni carby from an early 1970s TM125 Suzuki MX bike and it runs well too.

Yes the KT is not as easy to ride in sections as the more popular mid-1970s bikes however there are some redeeming features: Lots of people have never seen one and want to know more about them when they see one. They have great styling. Trying to agree on which design concepts were stolen from the other brands is a great discussion topic. If you are a bit of a gumby rider, riding a KT is a good excuse to use for your high score. The front brake arm is an amazingly distorted piece of steel and is way over-designed (another good discussion topic) They are a terrific trailbike - even better than a TY or a TL250. The straight cut primary drive gears make the coolest whirring/whining noise under load. With a few changes to the suspension, they really aren't too bad to ride in sections. Don Smith was involved with the development and I reckon that's pretty cool.

Yes you can buy decent shockies for TY175s in Australia Don Newell (07 33531874) in Brisbane imports Falcon shocks and usually has the right size in stock for TY175s. Peter Schoene in Victoria (03 51489191) (Bultaco Parts Australia) can supply the right Betors for the TY175. I suggest if you want to contact the Sammy Miller shop that you phone them rather than email. David

Scotty if you are having problems with the tiny standard Yamaha footpegs but don't want to spoil the original look of the frame, you can extend the standard footpegs to make them more comfortable. Have a look at the B&J Racing website. They sell kits for exactly this purpose and even offer a service to do the welding for you. The TY mono pegs aren't much bigger than the TY twinshock pegs. Why bother with them? That bit about using plates to use standard modern footpegs is really the best option. I have done that on my TY250B and the difference in comfort and balance is astounding. It looks fine if the plates are neatly made and colour match the frame. Email or PM me with your email address if you want photos. What is the problem with welding plugs into the bottom tube anyway?

My guess is that it is not likely to be interchangable. The TY250N-R motor is a different series to the motor used in the Twinshock TY250A-E.

If you are going to try the rocking technique, use top gear. It puts the highest torque on the clutch.

Well spotted. Great footage. Thanks

Copemech The Monty 348 and 349 do indeed use shimming on the top end of the conrod to keep the conrod in the middle of the big end. Not all bikes are designed the same. Vive la difference. Roberto I don't know what the minimum should be but mine seems to go fine with about 0.5mm clearance with a standard conrod. Note that some aftermarket conrods for 348s and 349s are wider in the middle section and may need very careful setting up (and maybe machining of the crank halves) to make sure the rod misses the crank wheels. David

Yes. It's a good one isn't it? Maybe Nick already knows where stump magnet lives.

What do the magneto cover dowel holes and kickstart shaft look like? If they are bent out of shape it might have been a crash into a solid object that did it. Otherwise I can't see the fracture surface well enough in the photo to see if it was fatigue failure or not. Typically 348 frames crack just under the steering head if the bike is ridden very heavily. There was a factory recall that added gussets at the steering head to the early model 348s. Later ones had the gusseting from new. I have three 348 frames and none of them show evidence of cracking or crack repair work there. Apart from that issue I reckon they are a great frame.

I bought that WISECO piston kit from my local (Gladstone, Queensland) Yamaha dealer. I'm sure any bike shop worth it's salt in OZ could get WISECO piston kits. An alternative for you would be to buy one from the US (say from B&J Racing). For us here in OZ the total cost of some items from the US is quite competitive with local supply due to the low freight rates from the US.

I used a 0,5mm oversize Wiseco in a rebore 3 years ago of my TY250 twinshock and the piston has been nice and quiet mechanically at all RPM ever since. I haven't even bothered to fit the rubber blocks to the fins.