bulto58

Go for a Electric Motion. I'm 6ft and bought a Oset 24.0R new last year, I was impressed with the power of the bike but handling over obstacles was hard work. kept it a few months and swapped it for a EM. It was definitely the right decision , 100%!

It's got to be Airoh !!

You won’t be disappointed owning one... loads of power, 3 map settings about 2 hours ride time from full charge. I enjoy this bike as much as my 4rt

I used to get the cut throat sign from the wife until I got one of these.

I've done this on my 2016. fine metal mesh , fold to the plastic edge's of the hole, rough up the plastic first, then used heat resistant silicone. All stayed in place.

Got in touch with sandifords again for an update on the Mecatecno T18 , due out in June. But seems Sandifords have ceased working with Mecatecno, so is there another UK importer.

Whats the opinion on ," Install new O Rings in filter cover" as the manual states, for the oil and filter change. Is this every time ?

Old box spanner with a slot to go over the pin, and compress the spring.Easy to pull the pin out, but not so easy to get the bugger back in.

I could be in the market for a electric trials bike. like the EM 5.7 , is there any upgrades from the 2017, is the 2018 out yet ?. EM web site or Facebook page don't give much new info. I do like what I'm hearing on the new Mecatecno T18. any info from you electric bike guys out there.

Just reminded me why I got a 4RT

I had a Mikuni on my MAR, it came with 150 main jet , and 35 pilot. You might need to experiment with other size jets, for correct running. The mixture screw is on the right of the carb, it is slotted brass facing up at you when on the bike. Should be about 1.1/2 to 2 turns out, with hot engine.

Push the choke lever up as high as you can, and hold while you kick it over. I used to need to do this on my old Sherco, found I could wedge the lever against the frame, worked for me.

Yes, I was there. what a great show!!!

I have had the same experience Spen, my Bully's never see daylight , since I got myself a 2016 4rt, what a machine, it puts the fun back into riding a trials bike , with what you can do on it with ease.

My last MAR 250, I fitted a new Mikuni VM26 and with many jet changes, I ended up with 155 main / 35 pilot. And yes the air jet was 0.5. and dropped the needle clip to 3rd notch down.

Thanks for the video and Info ' guys '

Is anyone using a db killer on their mont Do they do the job , without effecting performance . Where are they available to buy , for 2016 mont Thanks.

Just did the first oil and filter change on the new bike, all went well, let the bike run for five minutes, no leaks. Next day went to put bashplate on, and noticed faint line of oil on the centre gasket line, so gave it a good wipe off, and checked the drain bolt, all seemed dry.l've looked again today and the faint line of oil is back. I'm not sure now if this could of been happening from the factory , it doesn't cause a drip,just this faint line of oil. Also what is the small hole on this case joint, could it seep slightly from there .

Hi to all, I'm going to be changing my oil's and fillter for the first time, and have all the info to carry out the work, except for the torque spec of the casing bolts. would the bolts on the clutch side be the same Torque ( for future reference ) Thanks.

Don't know how many of you guys have clicked on the news of Franz Kadlec,but that is some amazing photography of the young German, on the point of no return

Hi 4rt owners, I'm just about to pick up my new 4rt standard this week, my first brand new bike for years , and have been looking at various carbon/ ABS covers to protect it from new. how do you guys rate these products, and what would you say are a must have ! Does whats on the market at the moment fit the 2016 model, will 2015 parts fit. I was looking at the thicker bashplate from H&D, it must be stronger, but is it wider to protect the casings and waterpump. Thanks.

Did you put the alloy spacer between the head and cylinder on assembly, And if so what thickness. Just a thought

Have a read in website news ( login issues ). You will see what everyone's been moaning about, But nothing's changed!!

If I ride my M91 ( I do love that bike ) then get on my 198À, the handling is so much better, but others might say different.

Yeah, that fix didn't last long it's happening again, are me and ripgrove the only ones , or is it happening to other members. This is being sent from iPhone I hope