feetupfun

From what I have seen, the other Montesa trials bike square section fork bottoms from the same era look the same as the 348 and probably are

As well as those things Tim said, if the fuel evaporates out of the float bowl over time (fuel tap off and does not pass), it leaves a viscous oily residue coating on everything that it was touching that takes a while to wash off when you turn the fuel on next time. I find that I get restriction in the pilot jet from this residue that makes the bike run poorly for a few minutes after not being run for a few weeks. With longer term storage (with the fuel tap left on or passing) a solid polymer film can form on the surfaces that the petrol touches and it can be very difficult to remove the film.

1974 was the first well-known Yamaha single-shock trials bike. It was a Tilkens (non-linkage) design rear end like the early YZ and MX Yamahas. Mick Andrews rode the SSDT on it that year. The first Yamaha linkage-type single shock trials bikes were in existance in the early 1980s as development bikes but the design was not "revealed" until 1983. There were probably home-made single shock trials bikes before Yamaha started making them.

Not a dumb question at all. Yes some people run with less spark advance than standard on trials bikes, especially on large capacity motors. The standard setting is only a guide. Why not try it and see what you think. The motor will run even with the spark after TDC so you can experiment to your hearts desire. To start with I would try 10 degrees BTDC and see if you can feel the difference. Remember to test for the effect on high RPM performance as well as low RPM response.

Wossner are making pistons 4 mm oversize for some patterns so that might be the source for a 74mm TY250 piston.

Replacement (unobtainable) magneto covers for Yamaha TY250 twinshock or TY175 Twinshock bikes would probably be suitable parts for the case study although they would be less of a challenge than a one-piece airbox.

Those KLR 650 motors are fantastically long lived. You can expect 50,000km before it will need rings and a cam chain. If they stil have the CV carby, the fuel economy will be good too. The only downside I know of is that the suspension is 1980s trailbike technology so while it will be smooth riding don't expect it to be up with the latest bikes on broken ground. The hot ticket I remember for improving the front end for off-road stuff is to fit a TT600 front end (clamps, forks and wheel)

Front uprights shorten at bottom end. Rear uprights shorten at top end. Middle uprights shorten at top end.

My IRC fronts have been very slow to wear. The rubber feels same softness as Dunlop to me when new and carcass stiffness is also very similar to Dunlop ie carcass not as flexible as Michelin given same pressure. All proper trials competition tyres have softer rubber and are more flexible than the Pirelli. I have never been able to wear out a front trials tyre before the rubber goes hard so maybe I'm not the right person to give an opinion about which competition trials tyre is best for intensive long distance trail riding.

IRC fronts are good value in Australia and are much better to ride with than Pirelli fronts. I rate IRC fronts along side Dunlop fronts but not quite as good as Michelin fronts.

TY250 twinshock gear change shaft replacement does not require the cases split, but does require removing the clutch cover and the clutch basket. There is a circlip on the LH end of the shift shaft and once it is removed, the shaft slides out towards the right. Replacing the shaft is probably less work than repairing the cut-off shaft.

You could try a few more different solvents. There is bound to be one that works (alcohol, acetone, toluene, ether, citrus cleaner, hot water and detergent, dry cleaning solvent.....

Monty primary drive gear is on a taper which can be very difficult to separate. There are previous postings on the ways people have got the gear off. Yes the seal holder is just like a Bultaco.

If something snags the cable without safety wiring, the outer can pull out of position and may return on its own or with some assistance, but the outer does not see a tension loading (the inner takes the tension load). If the outer is safety wired and then is snagged, the outer may be stretched which would probably leave no options for continuing riding as outers cannot be recompressed once stretched.

I don't care which side, but I do care how ergonomic they are. A few years ago my wife wanted a modern bike and the choice was down to a Beta Rev 3 (left side kick)or a 2 stroke Yamaha motor Scorpa (right side kick). We bought the Beta because the end of the Scorpa kickstart was so high she couldn't get her foot high enough to reach it. She had no probs starting the Beta.

Samy this is to give you info about the sort of battery duration that is achieved with an OSET. My son has been riding an OSET spider 16 since 2007. During that period his weight has gone from 22kg to 24kg. The riding time capability on one set of batteries is marginal for a kids level one-day trial. We usually managed the issue by having him warm up on one set of batteries, then change to a fully charged set at the start of the competition and they would sometimes last the whole trial and sometimes not. We did manage OK this way but having three sets of batteries would have been better, especially if his sister also wanted to have a ride, or if he wanted to continue riding after the trial. If cost had been no object we would have had eight sets of SLA batteries (sixteen batteries) for two-day events. At home my son practiced trials on sloped ground and one set of batteries would last about 15 minutes of constant riding, and less if it included much riding up slopes, and maybe 30 minutes of constant riding if it was mainly on the flat. David

No pollution? Where does the electricity for charging it come from?

The current Scorpa is a bike designed and built by Sherco. The "Yamaha" in your photo is a Scorpa from when Scorpas were made by Scorpa and powered by Yamaha motors. Have a look at this 2009 250cc four stroke Scorpa and you will see the same frame as in that photo of the "Yamaha" http://newmotorcyclebuyersguide.com/scorpa-sy250f-sy200f-sy125f.html

Much better to pull the swingarm out to grease the bushes anyway than to use a grease gun Removing powder coating - its just plastic that melts as it is heated so if you can heat it enough to soften the coating without wrecking the coating on the areas you want to keep coated, then just use a paint scraper. If it was me I would use an electric industrial heat gun (paint stripper gun)to locally heat the steering stem and scrape it off as it softens and bubbles.

Think about it mate. Your topic says "fun in the garage" - people read that and have no idea what it is about so have a look. Most not interested and so don't reply. No wonder 500 views but many less replies. I was interested in replying about the bike until I got to your insult

Wow

My understanding is that the function of the pickup is to generate a pulse as the magnet passes. Maybe your resistance measurements across the pickup coil are being corrupted by that pulse

Oops! I've just deleted some messages so it should work now

It does look like the header pipe has a tighter bend

I just had some custom made in Brisbane, Australia. Price was fine but but freight might be prohibitive from there to the USA. You can PM me if you want the contact details for the person who made them for me.