Beta

i've recently bought a beta 250, the clutch has gone and i don't know the year of the bike does anyone know how to find out from the frame number?

Hello, After spending all my evenings in the week and Saturday going over the bike to get it in a good ridable condition I took it out today for the first time, it all seemed good for the first couple of hours except a false neutral I kept hitting any time I tried to go north of 4th. Then without explanation it got stuck in gear, I came to a stop and tried to find neutral, no luck, killed the engine and tried to find it but the foot pedal will move a little either way but won't disengage whatever gear it's in (I think 4th or 5th). Anyone had similar issues and/or have any instruction on gearbox/selector dismantling? Regardless of all that, I had a real good time on the…

After dwelling on the forum for a while and bargain hunting, Purchased a 2008 beta rev3250 , loads of trick bits on it , but the "CLUTCH" isn't working , or so I was told , anyhow dropped the oil this morning and it's mud brown ( obviously water in crankcase ) . Then I look at the oil drain plug and ouch I realised what I've got involved with !! Spoiler Spoiler ( sorry can't remove the spoiler box ) Any guesses what I'm going to find inside the casings ?

Hello everybody,apart from the evo's own front wheel which other beta model front wheel will fit the evo? Thanks.

just changed mains and crank seals and noticed there is a bit of a clunk when you spin the sprocket cog anything i can do b4 i put the rest of the engine together cheers mick i think its called the output shaft if you rotate it eitherway fast it gives a clunk it did it when i rode the bike complete a touch of throttle and it was like the chain slapping at least thats what i thought untill i split the engine

Not to start a big oil thread, but I was wondering if it's OK to use Motul TransOil Expert 10-40 in the engine. The dealer gave it to me, but I think he gave me the incorrect bottle. Does anybody use that stuff?

Hi there Just bought an 125 rev 3. Frame number is zd3t3000040000037. Is has 04 stamped on the cylinder. Is all this pointing towards it being an 04 ?

I've had a small squeak in the rear end about half way into the stroke for a few hours so went to work on the linkages yesterday. Checked all bolts - found a loose top mount. Squeak still there. Pulled the linkages apart and re-greased, 50 hours since last re-grease. Found one rear dogbone bush that's case hardening has broken up, but other than that all good. Reassembled everything. Squeak still there. Very nearly decided to just ignore it and assume it was an overflow hose or something rubbing, but resisted and kept hunting. Tightened the bash plate bolts. Still there. Checked the rear engine mount - bolt was considerably loose. Tighten that and sque…

Hi, I am changing the kickstart spring on a beta 80, I have drained the oil and the coolant, can I take the cover straight off without taking the water pump cover off, any information on this appreciated, thanks

hey, i have a 98 beta techno, is there any way i can improve low down power, or overall power. ive just repacked silencer, how can i get more power from the packing and could i fit different jets? thanks

the engine of my beta has discoloured where the leaking carb has leaked petrol onto the engine, is there anything that will bring the colour back thank you

Hi all, my mate got a 01 rev 3 250 today got it home turned the petrol on and it just pours out the bottom of the carb ?? i see there is a lot of problems with the later models is there a mod that needs doing on a 2001 ??? Regards Scorpa250.

Does anyone know the reference number for the bearing at the bottom end of the rear unit?

after 3 years of ownership just had to replace my first ' dealer only part' on my rev 3. eventually succumbed to the need for a replacement inner clutch casing to replace the leaking original. used the link on this site to get a phone no. rang Silsden, the chap knew what i wanted but said they wouldnt be able to get it to me till the weekend ( this was tuesday tea time!) well, parts were delivered 'recorded' to my door with every seal, gasket, nut and bolt I needed to do the job and by friday 10am the bike was up and running.. now thats real service and decent value as well ( part, service items, recorded postage and VAT =

Does anyone know where I could get a repsol graphics kit, or even some swingarm and fork decals for my 2007 rev 3. Any info much appreciated

Hi agin, just about got the bike back together but i cant see where the cdi unit mounts, its a 1998 techno with the seperate cdi unit, i have the rubber bracket and the metal bracket but cant see any room to fit it, if you have any pics or advise that would be great and very helpfull cheers Paul

I need a couple of spokes for the 18" rear wheel on my 1993 Beta Zero Gara. The wheel is an Akront. The Beta specialist I've been in touch with has sent me spokes, but they're too long. Anybody got any suggestions?

Does anyone know if the lower shock bolt and special nut on Rev3 2000 is the same dimensions as on the newer beta rev3 models 06, 07?

please can some one tell the ohms value on my 125 rev 3, at the moment the primary low tension reads 1.5 ohms, and the secondary HT wire is 9.59, is this about right also is there a way to test the stator out put on the bike

Hi! First, sorry my bad English, I recently got a 1995 beta techno that came with a Paioli USD fork. When I was cleaning it, I noticed that it had some electrical tape between this metal part where the dust seal is mounted an the fork legs. When I removed it I noticed that this metal parts can spin and my question is if this is normal on this kind of forks. I'm attaching a picture I found online so it's easier to understand. I still haven't used the bike as I'm still repairing it but I guess the previous owner put that tape because it was losing oil from that joint? Thank you!