Beta

In regard to the (2) ports in the case, one on the clutch side, the other on the flywheel side... My '96 Techno connected these two ports with a single line. Overflow would dribble gear oil into the flywheel side. My '04 Rev3 has 2 tubes, each going from the repective port to the ground. Interestingly, the Techno was spotless and corrosion-free under the flywheel yet my Rev3 is dry with moderate corrosion... Which plumbing is best?

The owners manual says that the brass colored screw that adjusts damping adjusts compression damping. I have adjusted mine and found it to adjust rebound damping. Is there a typo in the manual or am i incorrect.

hi, i am just about to attempt replacing the fork seals in my lads 07 125 beta and just wondered if anyone has a nice clear and easy to understand piccy of the parts of the forks and there fitting sequence etc. ps i gather from what i've read recently that 7 weight is the oil to go with ? many thanks for any help

During my clutch inspection I found two steels that had lips along the outer perimeter on one side that the adjacent friction fits nicely into. These aren’t mentioned anywhere in the manuals I found, do they go in a special location in the stack? The frictions were all within spec so I reassembled as it came apart and flipped the spring washers so the raised area was nestled inside the spring, lowering the effecting preload pressure on the springs. Clutch is a lightswitch, I’m hoping to get more progressiveness in its action…. Thoughts? Skiddy

Hi All I am taking the cylinder head of a 2006 rev 80 but the head bolts and barrel nuts appear to be loose on a 10 mm spanner but 9mm wont fit. I just want to know if I am missing a trick and they require a special beta spanner. many thanks

I have a 2001 Rev3 that is a little sharp off idle so I would like to try a weight. I have one for a 2008 but it is a different size. I can make one. Does anyone have any details like diameter, thickness weight or even a picture. I find nothing on line.

hi guys does anyone know where i can buy just the seals for the front brake caliper on a 2015 evo theres nothing up with the pistons there practically brand new i can only seem to find the kits surly some 1 must just do the seals ideally uk thanks

Anyone got one yet? Any reviews/thoughts?

Hi all been reading about the changes done to the 07 08 rev 3 , and I was wondering if the weight that was added to the primary fly wheel could be removed for a snappy throttle response as I had a 05 rev 3 250 and liked how it was on dilivery and when I fitted the weight to that I did not like how it changed the engine character so I'm wondering if the same will be with the 08 . Thanks

Hello Looking for frame protection for Beta evo 2021 factory . frame protectors/swing arm /fork protectors etc can you advise best place to buy.

Hi all, could do with some assistance re an issue experienced at a trial today. I have a 2008 beta rev 3. I managed to 5 section 6 today at my local trial, what was actually quite an innocuous looking bank. The bike went down on its side (all rather slowly and painlessly) and started to gain and gain revs (second gear, rear wheel was in fresh air going ten to the dozen). First thing I noticed was that the throttle wasn't stuck open. When I eventually cut the engine, and got the bike upright, the bike would not kick over. I noticed immediately that there was no resistance/a lack of compression when I tried to kick it. Each time I kick it in neutral it's as light as a feath…

Does any one happen to know what the paint colour of the frame is called or the colour code, or where I might be able to get it made up, or buy it in a spay can. Thanks Mike.

Hi all after taking my flywheel off on my 2015 factory Beta 300 need to get a puller but not sure what one...... had a look on eBay and there’s a few different ones ? M30 ??32mm thread ???

Hi All, My 2008 Rev 4t needs a new water pump impeller as the plastic one has cracked and the bike is running very hot. My question is, I have seen the Apico/Jitsie upgrades for the Rev3, is anything similar available for the Rev4t? Just a suggestion for a metal impeller that fits would be great. Thanks.

Ho all what is the numbers for on the bottom yoke or has my bike got data frame numbers for theft registered bike ?

hi ,has any one tried some boyesen reeds in a 125 evo? any jetting changes required ? cheers guys

So NGK. Tells me to use a BP7ES. Went to get a new one from local shop and they did not have one. I can get one online I am sure but I was thinking could I just put in a B7ES OR A BR7ES.

Right, I recently replaced a fair few bits on my 96' Techno because the water pump seal had gone, that included the shaft as it was showing slight wear from the seal, and I did the bearings & impeller at the same time. The shaft now supplied is a 2 piece assembly with a nylon drive gear, not all steel as the original. It matched up ok, and seemed to go in fine though. However, upon reassembly and running it for a very (very) short time, there was a 'graunching'/grinding noise that I didn't like, so I stopped it quickly, and I've had the clutch out again tonight, only to find there are lots of little bits of white nylon in the bottom of the clutch case, and it woul…

Hi, can anyone tell me, is it ok to remove the water pump cover while the bike is stopped ? and if so, will it pour out of water ?

Hi, removed the switch gear from the bike and fitted a kill switch, connected the 2 yellow wires together and put it all back together now the fan will not work ? it was working previously, there is also a black wire coming from the connector block that is not connected to anything, any ideas please ?