dan williams

Hmmm like years of crappy clutch plates? It's important that Beta get lot's of feedback that this is unacceptable so they can take it back to their supplier. Maybe this is the start of the Chinese parts invasion. Maybe not. You'd hope Beta learned the lesson from snapped frames on the 2009 Evo that there are places you can save money and places that you had better get right or profit goes to zero. Right now fenders look to the factory to be a revenue generator. They need to hear right now that this will hurt them in the long run and they better get it sorted "muy pronto" or it's going to cost them bike sales. All you guys who've snapped fenders should contact them through their website info@betamotor.com.

Understood. I've taken to shooting mostly RAW to get more dynamic range. Then again I built a beast of a system to do the conversion and get the most out of the highly threaded Bibble software. It does help recover usable stuff when I completely Melvin a shoot with the wrong settings. Not that that happens, er alot.

Yup bend the tang the needle valve attaches to to set the float level. Bend the little tab that points up at a right angle along the pylon that holds the float pivot to set the float travel. Don't be afraid, it's not as scary as it sounds. It'll be pretty obvious once you pull the float bowl off.

You guys have to realize it's not as simple as throwing your bike in a transit and showing up at the event. There's much more involved and it takes money. Money that wasn't there from the sponsor and money that Ossa can't afford to spend just yet. A factory has to answer to the sponsors or there is no team. Riding Sheffield without the sponsor could have blown a deal that I would guess took months to negotiate. I'm sure they were more frustrated then any spectator or organizer could be but it's a business first and a sport second or they won't be a business very long.

Yeah the Billy T article opened my eyes. Nippering a small hole in each of the vent tubes halfway up the carb body stopped the fuel leak siphon problem on all the bikes I've done it to (~10). Works like a charm, costs $0. The extreme angle the Beta carb sits at helps it run strong on steep ups but requires the float level be correct or slightly low or it will stall on downhills. I've found this to be true on the Mikuni and the Keihin.

You gotta love Fuji, he's a one man highlight reel. Andy are you shooting raw or doing JPGs out of the camera?

Maybe Jeroni should borrow Billy T's kilt.

I hope they'll be posted soon.

Heh heh, you're forgetting the factory makes more money selling the riding gear then the bike. From that perspective the excuse makes sense.

Yeah that's just the way experts like them. Trials brakes don't "chase themselves" into engagement so they're unlikely to be malfunctioning just that you haven't got the feel for them. You can try letting the lever adjustment out further so they engage nearer to the bar or moving the perch closer to the end of the bar to reduce your finger's leverage. You could try filing grooves in the pads to reduce the surface area of the pad. My guess is you're just not used to them. Remember more then one finger on the brake is too many. If you're throwing two or a handful at the front brake like it's an old drum brake Bultaco any modern bike will put you on your head.

Yes this week. Tried propane torch on cylinder with no luck. Waited until it was near 50F out and it kicked right over. Opened ignition side cover and drained the water out. All good.

Can you be more specific? Are they grabby when you use them in a section or are they grabbing just by themselves? I don't know your level of experiance or ability so please excuse me if this comes off as me being a jerk. The top guys actually like their brakes to be really strong so there may not actually be a problem with your brakes they may be quite good. I've found some top expert bikes to be unridable for me as every control is light switch fast. Likely issues that can affect the brakes is if the bike has sat for a long time with the pads in contact with the rotor the surface of the rotor can be uneven and the braking will seem grabby because the area where the pads were will work better then the rest of the rotor. The same happens if the rotor is contaminated with oil or brake fluid. micro-fractures in the metal will retain a small amount of oil causing the rotor to not provide the proper friction. There are some contaminants that can cause a rotor to be stickier. Again if this occurs in an uneven pattern across the rotor the result can seem like intermittently grabbing brakes. The other possibility is the pads being contaminated but that usually results in brakes that are weak. One of the common "cures" for contaminated brakes, other then changing them out, is to do some high speed runs dragging the brakes to heat up the rotor and pads and then when they are nice and hot throw cold water on them. I know it sounds ridiculous but it actually works. The other is brake cleaner which can work or it can just spread a contaminant. In theory brakes are very simple mechanisms so usually there's a simple fix for just about any problem. It's just figuring out the problem that's a pain. One thing to make sure you don't do is the rookie mistake of fixing the rotor in place. Trials bikes use "floating" rotors so there is play in the rotor mounting to allow it to self center on the pads. If you torque down the rotor bolts and don't break the hub (a common result) then all bets are off. Grab the rotor and make sure it has some play in it. Please lt us know what you find.

As usual Billy I agree with you. I also hate the MTV style of quick edit and I hate the "focus on the rear wheel" just as the rider is doing something type of shooting. It's a tire, it's almost flat I get it. How about showing me what's going on on a bit more of a macro level.

I run VP C-12 so I also have no issues but I have also run CAM2 (Sunoco 110) race gas and noticed waxy residue on cold fuel bottles that doesn't occur with the C-12. Interesting note from the VP website FAQ: What type of 2-stroke oil should be used in C-12? C-12, C-14, and VP Red work very well with synthetic or petroleum based oils. However, bean oils will tend to separate below 35 degrees F. in fuels with a specific gravity of less than .730.

Like these Runners

Ah, pardon the colonial. As in cake frosting. I get it now. We may be in agreement again. Separation of low volatility hydrocarbons from the fuel mixture. I thought people were actually talking about water ice. My apologies.

For the Betas I've worked on the 2 1/2 plastic PVC pipe cut to about 24" worked perfectly and cost only a few dollars. I also have 8' of extra to make seal drivers for my friends, or one for each fork leg of two bikes, or a didgeridoo.

Accepted but what's being described sounds like a fuel volatility issue. "Carb icing" is something that doesn't affect starting until after the engine has been run a while and will kill the engine while running. Which is why it's so feared in aircraft and why airplane carbs have heaters built into them. Also bike carbs are behind and in close proximity to the cylinder (except the Ossa) so they have a tendancy to be self heating to some extent after the engine has run for a bit. I never had this issue with my old Bultaco which on hot days could boil the fuel in the tank. The Beta tank, being a big heatsink, has no problem. I've often wondered why they didn't go the extra mile and use the frame for cooling to save weight. Couple of thin copper tubes down the frame rails wouldn't have heated the frame too much but spread the heat out requiring a much smaller radiator.

I've been beating that drum for 20 years. In New England we actually made a major effort several years ago to cater to the lower riders so they would have fun and bring their friends into the sport but we've slipped away from it again and membership is falling dramatically as older riders leave the sport and newer ones get beat up in the lower classes and quit.

Not sure I would call it "carb icing". That term is commonly used in aircraft and is actually a problem on warm humid days when the air at altitude passing through the venturi and then expanding drops the temperature of the incoming air to the point where moisture precipitates out into the carb throat and freezes. It doesn't happen in cold dry air. I think what might be more likely is the temperature of the fuel is so low that it isn't vaporizing properly. Jetting it richer helps some as would adding something to the fuel that increases it's volatility. In the U.S. fuel mixtures are changed for summer and winter and if you are using a summer fuel in the winter the vapor pressure might be too low to ever work properly even if you re-jet. http://www.kellyracingfuels.com/rvp.html

I have fat bars on my '08 Rev3 but I don't let the hooks sit on the bars anymore since I noticed wear on the bars from them moving during transport. Kinda freaked me out knowing how little it takes for a stressed piece of metal like the bars to snap once they get a knick in them. I use runners (strap loops) that climbers use to carry stuff. Just loop them around the bars and attach the tiedowns to them instead of the bars.

You can't go wrong with the Renthals.

Yeah there's nothing like heading out into the woods with a snow shovel to clear some sections. It's quite surprising what you can get up when you can't rely on power and traction and have to use all weight/unweight and momentum. Dress like you would for skiing, in layers. The things that will get really cold are your feet and hands. I find when it's really cold warming the cylinder with a propane torch for a few seconds gets it started much easier.

Not sure about the seat but on a lot of bikes after the retaining bolts are removed the seat slides back out of a tab/loop type deal so try sliding it backwards. It might also be the seat and fender come off as a unit. The filler is the aluminum bolt with the hex hole in the top. I think the other bolt is the spring/plunger that indexes the shifter cam. Where in NH are you?

Actually it's "Watch out where the Huskys go and don't you eat that yellow snow" ... and right about that time people, a fur trapper, who was strictly from commercial, started into whipping on my favorite baby seal...