Aprilia

Hi , recently got into trials riding so purchased a Aprilia climber to start off on as it was cheap and in need of a bit of tarting up . I have stripped the forks down to find nothing about what oil to put back into them . They are Marzocchi 35mm stantions , they are on a 93 model too. Any help or info about this bike would be welcomed . Michael.

Hi guys Anyone know where I can get hold of original clutch cables for either of these bikes? They were more flexible than the latest Venhill cables and it helps with routing Please help!!!!! Dave

Anybody know which throttle and which carb was std fitment on a 1992 - 1994 240/280 ?

hi, can someone please help. i have a txr 240 that did not come with a carb. i need the specs(ie jets sizes etc) for the dellorto phbh 26mm. any help will be much appreciated. regards willie.

I've been offered what will end up a very cheap Aprilia Climber in a deal but the owner is unsure of model year..........It's either late 80's or early 90's I think. I assume that I will need to get the frame number to date it accurately rather than just go by the colour scheme? If done by frame number can someone please point me in the direction of where / how to get it dated. My experience of Aprilia road bike dealers & spares availability has been pretty poor, so advice on who to contact if I need parts would also be gratefully received. Thanks

Hi I have just bought a 1993/4 ish climber as a non runner. Some one has been in at the disc valve which was out, but I have set it as per the www.rotax.co.uk uk parts list instructions (I think). The previous owner has apparently changed the piston and rings due to low compression. The bike now has very strong compression maybe a little more than I would expect. I have checked over the carb and this looks to be set up just about right. 105 main jet and needle clip second from the bottom. I have tried the old squirt wd40 in the carb mouth to get over any carb problems. (I know this sounds a bit daft but its worked for me as an indicator for many years) This…

how do i tell what size motor my climber has ?

hi fella,s just joined this site and just aquired an aprilia climber , would appreciate some feedback on a couple of issues , iv,e had loads of bikes over the years but never a rotax jobbie and as you all know they all have thier own ways of getting on your last nerve . so first off bike runs for 5 seconds and dies ,cleaned carb out with airline , the same! mains are rumbling , plug soaked when stops ,and what is the 2 stroke mix on this bike , regards lee

Have a look at the early Aprilia towards the end, Hiro engine ? Also a good selection of SWM's,Italjets etc.

can anyone help me out,ive a 280 climber and the big end bearing has gone,i only need the bearing and not the full con rod kit,as this is to buy

Would someone do me a favour and measure the thickness of the spacers that go between the sump guard and the frame at the front. Thanks Ross

Hi all, I'm trying to find a replacement rear disc (ideally new) for my 93 Climber, anyone any ideas? I've tried EBC and no luck so far. Did Aprilia use the disc on any other models. Nothing showing on e'Bay at the moment either. Thanks Dunc

hello, My bike is, aprilia climber 240(1994) is spills oil from the gear/kickstart shaft, i think it spills it form between, what could it be? the other problem is that the gear shaft dislcoates from its place when applying little force on it towards the outside when trying to remove. please help! thankyou jose

just purchased a Can Am (Armstrong) CMT310 with the 323cc Hiro engine. I understand that Hiro was purchased by Aprilia, is there still parts available for these engines? Or for Armstrongs? Rick

Well a mate of mine over here needs one. Who is the man for aprillia spares? Help Please lee

I am rebuilding a pair of TX311 forks anyone know how much oil they take ?

can anyone help me replace piston rings on my aprilia climber 240,the size ia looking for is 71.95,i dont realy know anywhere that sells them.ive looked on rotax site and theres no information about the older bomadier engines,can you help me out can i get them from a main dealer,our does anyone have some for sale,thanks,

Hi All, does anyone have any idea what these are worth? are there any big issues with them? its a 92 , all there , all works as is should, needs a rear tyre (dont they all!) looks in better nick than a lot of 2002 bikes i have seen. any info at all cheers paul

Does anyone know where could i get new clutch plates for this bike or if they cross over from another one, thankyou

Hi Guys, Really could use some suggestions here. I am based in New Zealand and as far as I can tell Aprilia never imported trials bikes here. So, no parts supplier. Can any one suggest a dealer or supplier I could use to get parts? Cheers Iain