Gas Gas

I'm stock at 11/42 but do wonder how other options perform when you have more trails to ride. On single track the 4th to 5th jump can be a pisser in some situations, hehe thanks guys

hi guys! I´m building togheter my TXT 2006 250 and i´m wondering, how i should put the crankshaft bearings in. i´m not sure at which side the seal in the bearing should be => to the crankshaft or should it look to the ignition? i hope you know the answer, because i haven´t found anything in the internet so far. greets and thank in advantage Dani

Hi Anyone know who stocks Magura grips BUT not H&D Racing as i don't trust that web site as no contact details!!! Cheers

New Gas Gas 2011 125 with very sooty plug...unmolested carb and clean filter. What should I be looking for?

Hi all. Have recently purchased a 2007 Gas Gas 300 Raga rep, however it didnt come with a manual, and the gasgasmoto.es website has all the 2007 but the Raga manuals on . In searching for the manual should I refer to the 2008 or 2007 TXT Pro 300 or do I need to find the specific Raga replica manual? Thanks in advance for any advice! Jon.

I have recently replaced ignition coil on my TXT280 2000, but I am now unable to get spark. Checked all wiring, all seems in tact. Has anyone got any ideas what my problem could be please.

Hi, Does anyone know what pressure i should get on an Engine compression test when the bike is new ? Bike is Gas Gas 280cc 2008 Thanks Matt

Bonjour voilà 6 mois que ma moto gasgas txt 300 de 2012 n'avait pas tourner après un très gros entretient elle démarre mais quand je passe une vitesse mon moteur diminue de régime.que pourrais je faire.???? Attention je n'ai pas encore rouler avec. merci

Hi every i've been out on my bike today rode the trial got finished but theres a problem with the clutch.I've just give it a service with fresh atf dextron II & when riding it today noticed that when i was letting the clutch out to do some big splats it was slipping,if i just rode upto the the area i was trying to get up & did'nt use the clutch it would go up no bother but if i was using the clutch it would slip befor biting. i've not long fitted a new set of plates which were in tolerance with what gas gas recomend.By the way its a 05 300 Raga.

i got on my bike the other day only to find there was no clutch so there was feel to the lever but haveing not riden in in a while was unsure if it was normal so i tryed to bleed it then had nothing iv now bleed it sort of but removeing the circlip in the plunger it works but drags bad how do i bleed it proply i tryed rev bleding but nothing wound go into the res without the circlip removed i bleed it with the leaver removed also. hope someone can follow this and help?

hi can anyone help me please. after storing my bike over winter my clutch does not work causing the bike to stall when put in gear .i have changed my oil with the correct minarel oil and it has made no difference .any suggesions will be greatly appresheated .ps please excuse my spelling.

Hi are there any obvious differences between the 2007 and 2008 250txt pro that can be spotted in pictures thanks

Does anybody know if the exhaust from a 1993 Contact will fit a txt 2000. Cheers.

hi all splitting gas gas txt 50 boy engine can anyone tell me what size nut is on the clutch end of the crank please, apparently I will have to mill a socket down tried a 14mm and that was not it. Many thanks

Hello, Does anybody know the correct oil to petrol ratio for a Sherco 290 07, thanks

Here's some pics of the gas gas size range for anyone interested to see the size range lined up! It was my last chance to get a photo of them together as the little one was sold for christmas.

Long time no see guys.Hope everyone is well and enjoying their bikes. Been a turbulent couple of years since the death of my step dad and lots of water under the bridge as they say. So i have rebuilt my TXT 280 and made my mind up to trade it in or swap for a later model GasGas or a 200 Beta. Tending to go with the Gasser as the frame is easier to repair. Anyway hello to you all again.

Hi - this disintegrated whilst rebuilding the bike… any idea which part / part number it is? I can’t see/find it in the parts book. 🫠 07 TXT Pro 250. Can’t add or link it at the moment… it’s a plastic part that’s right under the headstock and the tabs come round the frame.

Hello, i need just alittle advice, apart from later for torque settings but ill try and get that infor out of <mention of this company is not permitted on Trials Central> Can i redirect you to the LAST two posts of this link http://www.trialscentral.com/forums/index.php?showtopic=6244 sorry to play silly buggers Mat

Okay guys any idea why my bike will not want to idle after riding for a bit