Beta

Hi All, Help please. I've read through the other forums on this topic but I'm still stuck. I've got a 2022 Beta Evo 2t with, I'm told, about 6 hours on it. I just purchased the bike last week. I noticed the few short rides around the driveway that the cooling fan did not turn on. The other day after about 30ish minutes of riding around the driveway the bike started to spit coolant as it was over heating. I wired a bypass around the thermal switch (unplugged and connected the two wires) and the fan turns on fine. I then assumed it was the thermal switch so ordered a new OEM Beta Evo thermal switch. I installed the new switch last night (very straight f…

Hi does anyone have a recommendation for clutch kit for 94’ Techno Thanks in advance

I am not a motorcycle mechanic and until I moved to Spain mainly had four stroke bikes. However a friend has brought his Beta TR34 to me because it starts ok but bogs down immediately. year unknown. I have dismantled the carb (Dellorto PHBH26 TD) and blown out the jets and airways but to no avail. Any hints and tips would be much appreciated. BC.

I bought a 10 month old Beat Evo 2010. When i bought it , the rear wheel bearings were shot so i replaced with new . I have had this bike less than 6 months and i am now on my third set of wheel bearings ( another DNF today ). I have heard a rumour that Beta have replaced these bearings with a bigger bearing to stop this happening again and it is a factory replacement if I get in touch with Lampkins. Has anybody else heard this before I get in touch with Lampkins and make a fool of myself !!! Phil

If anyone has a barrel gasket lying around can you please measure up the dimensions as I’m trying to cut one out of gasket paper. Thanks

Hi all. I've a 97 beta techno Dougie Lampkin replica which I bought for a decent price as it had no spark. This bike has a separate CDI to the coil and original coil is a blue Ducati one with only two wires, a live feed and an earth. I managed to get a spark with this set up however the wires entering the coil are on their last legs. I've also a (newer?) Coil pack with integrated CDI, the one with 4 spade connectors and an earth wire. 2 green, 1 red and 1 white inputs. If I were to use this instead, is it as simple as doing away with the stand alone CDI and taking the green, red and white wires from the stator straight to this newer CDI/coil? The yell…

I just purchased a 1990 Beta Zero and would like to get a wiring diagram and owners manual. Can anyone email those to me? I have done a ton of searching and nothing much comes up. My first trials bike! Want to give it a go.....i have been watching Dougie Lampkin vids and figure its not too hard......

Is there any kind of manual related to servicing the shock on a 2016 Evo 4t standard model? If not, are there any specifications for oil type, oil volume and gas pressure? I do see the remains of a sticker that probably said Sachs. I softened the fork valving and like the result so would like to soften the shock also.

Hi! I’m wondering if a 2010 Beta rim will fit on a 2001 Beta Rev 3? There is a guy selling a complete rim for a cheap price and my rim is broken. Stupid question I know… but I don’t have the knowledge. Best Regards!

Took muffler off during my inspection on the new to me bike and the o rings were hard broken junk. I’m trying to wrap my head around how the new ones will go on. Do they go on the Ti header first, then slide the muffler on, hoping they go into their prospective grooves? Seems optimistic at best…..

During my clutch inspection I found two steels that had lips along the outer perimeter on one side that the adjacent friction fits nicely into. These aren’t mentioned anywhere in the manuals I found, do they go in a special location in the stack? The frictions were all within spec so I reassembled as it came apart and flipped the spring washers so the raised area was nestled inside the spring, lowering the effecting preload pressure on the springs. Clutch is a lightswitch, I’m hoping to get more progressiveness in its action…. Thoughts? Skiddy

The spring that returns the tiny lever end has gone. The foldable lever end now collapses. Any idea where I can get a replacement? A new lever seems overkill.

Hi guys I could do with some advice I have been stupid and overtightened and snapped the right hand side Allen bolt in the top yolk I tried an easy out and it has made a mess so I have drilled down the side of the original bolt and tapped it for another which is now in and tight but I have little confidence in this now so I want to replace the top yolk but finding one seems to proving difficult but their is 38mm top yokes for, rev3,gasgas and sherco would any of these be a straight swap and fit or does anybody buly any chance have a beta evo top yolk for sale. Many thanks.

Hi All, I have been offered a 2012 Evo, black/red with 2012 on the rear mudguard but want to be sure it hasn't been re-stickered. Does anybody know if there is a year code as part of the frame number please? Thanks for any help and happy riding.

Buddy just picked up a 2013 Evo 300 and we went riding for the first time yesterday. the front wheel is visibly offset to the left when looking at the front of the bike. However. the fender is in the middle between the fork legs but the wheel is well offset to the left. Is this normal? We did check to make sure the axle was tight and it was so I don't know how we could get the wheel centered as the rotor also seemed lined up in the caliper?

I often find my Evo (300 4T) side stand sinks into the mud and there isn't always a handy tree nearby! You can buy aftermarket feet to increase the surface area for other bikes stands but can't see anything for the evo. Beta make one for the RR. It has a very small foot which doesn't make it easy to aftermarket feet to grip on. It does have a hole presumable for water. So guess the only options are to carry around a puck, find a welder or a better stand at the right length with spring holder that fits the standard bracket. Be great to hear if anyone else has solved this?

Hi there, i'm looking at buying a beta rev 3 and i have 2 bikes in mind, both the same price one is the 2005 beta rev 3 never been trialed and the other being the 2006 beta rev 3 its been trialed but only a couple of times, the 06 has a few usual trials marks where as the 05 has none, but im thinking the 06 is going to keep its value alot better but im just after a bit of help realy on what was the better engine etc the 05 or 06 Much Appriciated Reguards Richard

Beta evo 250 recently cleaned carb & runs fine only issue is I noticed the air screw is all the way in. Will this be fine. I screwed it out 1.5 turns & it made it run a little worse.

I've just taken delivery of my new Evo 300. I've always ridden Betas. My last bike was a 2020 Evo 300. Rode new bike for the first time on Fri. It is so different to the 2020. The 2nd gear seems like a gear I would use in every section now. On my 2020 I would always do slow tricky stuff in 1st but the 2023 bike will happily creep along the slowest section in 2nd yet still has the guts to blast up anything. Sprocket sizes seem the same. It must be down to ignition and mapping ? Has anybody else noticed a big difference? And they say beta just change the stickers ..........

Hello. I have a question regarding Beta tr32,tr33,tr34,tr35 and my question is: Does Beta tr32, tr33, tr34 and tr35 have the same engine and if not what is the differense between them? I bought one not too long ago and it is a TR32, I don`t know what year model it is. i belive its 81-89 Can you guys help me to find out? And by the way, does someone know where I can get parts or more information? Best regards, Bjørn.