Aprilia

HI can anybody please advise the oil mix for my TX300? ( Rotax engine) and at the risk of opening a can of worms; what is the best 2 stroke oil to use please ? thanks in advance

I've just bought a 1990 240 climber. The previous owner had a "throttle stuck open" moment before a tumble. He can't recall hooking the cable,is this a fault with a secondhand model? I'd also like to obtain a manual and spares in UK,is there a good dealer for these older bikes? Thanks

Hi all, I have aquired a 280 Climber which is now running but quite unstable at tick over and just above. I have found that the PHBH26CS carb which is the air screw version (not the petrol adjustment screw type) seems to be missing one of the jets. The Pilot jet is I think made up of 2 jets one is deep down and a sort of atomizing jet or idle imulsion tube as its´s listed (which is marked with 68) and there should be an idle jet "deep" sitting in front of this but it´s missing. Can anyone help with the size needed ?

Hi guys! Can anyone confirm whether this is actually the 2018 model? (LINK) My friend says its not but the sales representative claims that it is. I've been burned before and I want to take all precautions before going any further with this dealer. Thanks and happy riding!

Hi all, I have goten hold of a 93 Climber that was a non runner when bought. The seller had changed the electronic ignition box last year before putting it away (he said it ran then). He couldn´t start it this year and then the kickstarter snapped. I now have a spare kickstart fitted and got the bike running (rough with it missing beats at tickover). I cleaned the rotor and pickups etc. with brake cleaner and disconnected the handelbar switch after that it ran better but when moving the wires that come through under the tank it seemed to have a problem. I now have the earth cut off after the connector and have run a wire up to a kill button. She now want´s to st…

Iv got a climber purple tank and kick start dont seam too work it just spins the shaft any advice welcome as never worked with one help any workshop manuals about ????

Hi all I have two Climber 240 (91 and 92) in Japan. I am in the middle of my change the front fork oil project. I have some questions. 1. Oil level measurement (mm?) from the top of fork edge? 2. How much does each fork needs the oil (Aprilia manufacturer’s recommended ) 3. Recommended degree of viscosity. (or fork oil model number・part number) I don’t have a service manual of Climber... regards, Teru

Hi,all I have own Aprilia Climber 240. Also lost the spark , checked the plug, took the flywheel off and cleaned everyparts, coil and burn-in. Eventually I made a conclusion that doesnt work the condenser (ECU). I have one question. Please advice me how to remove the condenser that silicon bounded in the ECU box (CDI).. Any suggestions ? Teru

Any ID help with this Aprila Climber 240 # EO DGM 52584OM.

Hi all, I recently picked up an old '94 Climber 280 for pretty cheap. As such, it's needed a fair amount of work. As you all already know, information on these bikes seems to be pretty scarce. I just finished rebuilding the forks, but I am unsure as to how much fork oil to refill them with; any recommendations? Also, I heard that 5-7.5W is probably correct; does that sound right? If anyone has a good line on where to buy parts for these bikes, I would really appreciate it. I made an air filter and rear brake clevis, but would rather buy the correct parts. Thanks, Nick

Hi , whats the spares situation like on the 300TX for things like rear mudguards seat pads etc ? I presume Italy would be the best place to look or does anybody know better , thanks

I'm looking for an air filter for a TXR312M, I saw an ad a month or two ago that someone had reproduced them an I can't locate it. Does anyone have that information

Hi, I have an aprilia TX 300 with the engine block (crankcase and clutch) of an aprilia climber. Bring the original air-cooled cylinder. I would like to leave the clutch softer and I am looking for some docks to make it softer. Being a rotax engine may be worth the other models. Can someone help me? I will be very grateful. Thank you very much. Narciso

Hi im Dale from the northest of england,ive recently purchased an Aprilia 280 climber. I was wondering where i could get a wiring diagram or workshop manual, if anyone can help it would be appricated. Thanks in advance.

Here's a photograph, never published before, of a classic Aprilia in action. Taken by James Moorhouse it shows Ian Weatherill competing in the Yorkshire Centre Team trial in 1986. Enjoy - for more details PM me

Can anyone help me? My 1988 Climber was reving very high. So I suspected an air leak. I replaced the flywheel side crank oil seal, and found a little bit of play in the main bearing that side. Now it only seams to want to run on choke, and still revs quite high. Any suggestions? I was wondering about the carb boot the that goes into the side casing??

Hi, I've recently acquired a 1994 Aprilia Climber 280 but I'm having a hard time trying to find parts & a workshop manual for it. I currently need a new clutch master cylinder as the old Grimeca one has seized but I can't find an alternative anywhere? I also need to know where to drain & fill both the engine & transmission oils (I've been told the transmission oil has been drained).

Any source for Aprilia TXR312 rear sprocket? Does anyone know if the later model Aprilia Climber rear sprockets are the same as the TXR. Trials Shop here in the US is still on back order. All I need to get my TXR going.

After finally getting my '93/'94 Climber 280 rebuilt on Monday. The clutch is slipping like crazy. Post build I noticed gear oil weeping from the kick start/gear shaft seal so Martin at SWM Moto sorted my out. after rebuild number 3 the clutch slips terribly. Prior to this it had 10W40 in it. It now has ATF. I gave also replaced the clutch top basket as one of the fingers was missing. Nothing else has changed. any help or comments please, I'm baffled!