Gas Gas

Fan seems to be kicking in a bit more often than I remember on my bike (been a few years). Would this be a sign of a head gasket on the way out? Not boiling or emptying the rad, but the inside of the rad cap looks a bit dirty.

Hi i have a gas gas txt pro 250 09, I've just strip the bike for the frame and swimg arm to get powder coated as the frame had hardly any paint on it. The bike is all back together. (What a nightmare getting the rear brake bleed!) ?. The problem I have is the fan will not turn off when starting the bike. not sure if I've connected the right wire of the thermostat. ones wire to earth and other to the relay thing on the fan. Is that right? Or I have not bled the radiator correctly. Was all working before I strip the bike down. Any one got any tips of the trade would be appreciated thanks gary

Hi there, just got an 08 gas gas that still has the lights on and a seperate kill switch am i ok to just unplug the lights and tape up the connectors????? This may seem a stupid question but always had the lights removed at the shop!!! Thanks.

hi all i have a 2002 txt 280 standard for about 3 weeks. Still catching up on maintenance needed, and have attacked the rear suspension tonight and have found and not to my suprise everything dry as a bone!!! I've found an adjustment setting on the bottom of the shock that had been facing the engine and i didn't know it was there until i spun it around!! and i presume that it should face to the rear for adjustment? is this the rebound? My problem is the gold annodized rocker arms!! when i've spun the shock around they have reversed from the original position i.e dog bone to swing arm connectors, does this matter? or is there only one way to install them? Sorry f…

Anybody here rewound an exciter coil on a 280cc txt pro and be able to tell me what gauge/thickness the copper magnet wire is? (arnt the stature on all pro models the same?) Im asking as im Not able to measure mine untill at least Thursday but want to get some wire ordered first thing Monday morning. Cheers

Hi, I'm new to trials and picked up a nice JXT270. The muffler was shortened by the PO due to it being worn by the tire. What options are out there to get the OEM muffler. I was quoted $430 from Lewisportusa. Thats a bit steep. I only paid 1500 for the bike.

Can anyone advise where I can get clutch plates for a gas gas contact 200 1993. thanks

Hi,wondering if any-one can help.Ive got an early 1995 250 Gas Gas which has crankcase cooling,I seem to remember at the time the later models had it blanked off as they had trouble with bearings spinning in the casing.(I could be wrong)My bike has developed a water leak by the banjo bolt where it enters the casing as the casing has corroded away any-one any ideas if can be blanked off or if somthing needs doing in side of the engine as well.Or any ideas on repairing the casing? Many thanks

Ive got an 02 200 pro in need of rings cant find them anywhere in U.S. anyone know of a set

Im going to have a look at a -98 270 txt, i used to ride many years ago and im trying to get back in the sport again, depending on the condition, can this be something to start over with or should i directly look at later more expensive bikes? Is there any particular things to look out for in this model? I have attached a picture of the bike below. All help is much appreciated

Is 1600 a fair price to pay had a test ride and it was bang on and it is in nice enough shape Also are they any good anything to watch out for Any thing I should be aware of specific to gas gas or the 09 125 Thanks

Just purchase this trials bike this evening and trying to figure out model It did start on first kick but was unable to ride it. Would only continue to fire on 1 sec intervals at wide open throttle with heavy smoke. So just.. pop..pop..pop.

Quick question.. never have done fork seals on this bike, but it's leaking very bad. I have the seals. On my KTM I needed a Fork seal driver, but these zokes look a lot simpler. Am I correct in thinking the seal doesn't need a driver like the KTM WP Forks? Looks like you can simply slip it off.. Sorry for the lame question, but wanted to make sure before I tear them down.

Are the aftermarket top end kits on ebay any good? Dumb question? Wish BBR made a kit. What all should i replace when re-doing the too end? any good videos to share on rebuild? How to check if reeds are good etc…. This bike has been extremely reliable for many years! Even has a plate. Appreciate any advice and parts sources. What jetting is preferred and needle? I ride in WA state above sea level 500-2000’. not finding any help on gasgas riders club. Any other groups for gasgas ? i just did my sons CRF w/ a big bore kit (4 stroke). ✌🏼

I've was having trouble with my clutch when going very slow/stopped with the clutch disengaged or slightly dragging. Often, the point where it is slipping and engaging will be abrupt, not smooth. I was reading the sticky in the Beta forum about improving the clutch and know about the clutch basket filing method used for enduro and mx bikes. GG has a steel basket and I noticed very subtle grooves worn in the basket. The pull is as light as new and thickness is within specs. The clutch plate tabs were a bit rough, which I suppose is how they come from the factory. I did a very light filing on the basket and a super light filing on the plate tabs and the clutch abruptness we…

Hi everyone, its my first post. thanks for having me as a guest. I recently bought a 1995 jt25 that seems to have lived outside unsheltered. The steering bearings are totally corroded. I cant find the standard bearing number, using the parts manual in spanish. Would anyone know the generic bearing number? Also, i'm looking for close up pictures of the kickstand maybe near a measuring tape. Is the kickstand made of aluminum for this bike? I only have a few pictures from the internet thanks jason

Bonjour comment enlever le roulement à aiguille du fond de l'axe de kick. merci

hi all recently my bars have had the feeling of being a bit low down,whether lack of riding or older age or riding my mtb more, what difference do bar risers make in the handling etc thanks

I've done a search on this for the gassers but still a bit confused. It seems the rear is 6004 2RS but seems the rear is different or is it ?? Is it 6905 ? For a 2009 125

hi all i just want to know if any of the newer looking plastics fit the 2000 txt 50 as i want to make the bike look newer for my son as we cant afford a new bike just yet. thanks.