All Activity

I was riding and clutch was getting less pressure at lever until no pressure at all. I managed to ride back to truck. i found a burn mark on line by the exhaust pipe and lower was wet on line towards clutch cover. i opened master cylinder ( mineral oil) and was empty. I just sold my KTM 300 so have changed out my clutch line before but on the Gas Gas do I just unscrew the line from clutch cover and master up top and replace then use syringe to force mineral oil from bottom up? mahalo! riding on Oahu🤙🏾

& Aloha what island do you ride? 😎

Determine if your clutch operates on DOT brake fluid or thin Oil Determine if the problem is in the Master cylinder, brake line or Slave cylinder Replace parts and install is fairly easy requiring very few special tools outside of possibly a big plastic medical type syringe similar to in the picture below Easiest way to fluid fill is generally from the bottom bleed vent screw

Did it leak out where you can see it or inside the engine casings?

I have several front and rear mudguards to try out. Different makes, painted or unpainted, with or without stickers, with or without a light. I need to reconnect the rear master cylinder, correct the fork's compression stop, refinish the wiring harness, and redo the fork stickers. But it's starting to look like the '96 world champion bike.

Newbie here with a 2017 Gas Gas TXT 250. Clutch line leaked out on my ride today 😩 reservoir dry. had to ride back few miles with no clutch. just ordered a new line but how do I change it out? any help please Mahalo in advance!!!🤙

The engine needs to be rotating to change gears. To test, you must rotate the flywheel (or rear wheel) by hand while you operate the gear lever.

Hi ive had to buy as new selector shaft and after putting it all back together it doesn't want to go throigh the gears properly goes into 1st neutral and 2nd but thats it and the gear shifter does not return to center once it goes into gear have you got any advice? Thanks

https://www.thehellteam.com/brake-caliper-rep-kit-hebo-4p?srsltid=AfmBOopyq1w-7_-_H7ZJ41c2BBUTtNh2BAzMRGIADtm-L99l4MaROWy_ https://trialssuperstore.com/products/hebo-brake-caliper-piston?srsltid=AfmBOop738U4hM-MFl32cY7ZF5E-t010trpDNStAFOUEMrQ2BH6JsF8I https://www.ebay.com.sg/itm/224240631710

Hi, did you have any luck in sourcing these seals? I have the same problem on my 2001 txt 250 with Hebo calipers F&R. The calipers are not too bad, but I could do with some pistons and seals. All the best

"Shorting out on points cover". I sent my bike to two garages. Neither could sort it out. Finally I was looking at the engine when I noticed a little black mark on the inside of the points cover. It was arcing across to the cover and shorting out,

Try Hugh's Bultaco. www.bultacoclassic.com

Looking for an airbox for a M116....1974 Alpina 350....I'm in the USA

Hi, please see attached picture that's the one I'm looking for

https://www.ebay.co.uk/itm/335964704682?_skw=beta+side+stand&itmmeta=01JWBNETYSV4ZDXTA083F26MH6&hash=item4e390e8faa:g:1CYAAOSwHn5oJ4jA&itmprp=enc%3AAQAKAAAA8FkggFvd1GGDu0w3yXCmi1dNqfAsMuNA8W9g3U618jWbCw%2B58UW2nkSt0%2B%2F%2B%2BO1rojCvdV%2FmCc5bg7qH7LekqG9CRlfA%2BXvsZWIVVB%2BQthb8qdGuC1xtY3sp3AADBiqRMMbjr3dUhKS3kqhCIhl7aVTSRyYWkIutriR1Fv9vwAAo8VPdvCkvsCPj11lOG%2BYyLT5kqM4RrhB8DpU8mjvJYqmDfsbqAQublJ34iagvzUAnjT71nEblxQpP5yTDxK4C3%2F7FpI%2F%2BkZQwhqpdN3kDqoi%2FXiHdRzeebQVAaNSy2KCQcB0YHpfB8RZXHJNGOOXozg%3D%3D|tkp%3ABk9SR8ivu_XiZQ

In the UK? Try Allens used trial spares on FB

May be the last one Mitani tank available ...

There is no more space to fit adaptator like this.

?

The 2024 Sport has a clutch but cheaper wheels, suspension, console, and no phone app - but good enough for me

hi i have air box lid

After a bit more research (picking brains) it seems most likely to be for a 248 Cota. Surplus to requirements, so if you need one please drop me a line.

@ahell https://www.agbikes.co.uk/products/jitsie-keihin-carburettor-adaptor-pwk28