Gas Gas

Hi all. Just bought a txt pro 300, lovely bike question is, I’ve got an led headlight for it, found the connection on the loom, click it togeather .. and nothing at all, can’t find a switch and just can’t fathom it out. Surely it should be able to switch on and off? But I’m stumped… thanks for any reply…

Good Evening all! I’m looking at buying a TXT 250 Racing, 2021 model but I’ve heard too many rumours that they’re hard to start. I test rode one on Sunday and, to be fair, I had to get the owner to start it as it wouldn’t start for me. Is this a thing? Doesn’t make sense, surely it would put folks off buying them if they don’t start? My Beta Evo starts easy, I’m looking forward to the change as it’s a great bike to ride but will be mighty frustrated if I can’t start the thing, especially if I’m half way up a slippery bank! Can anyone enlighten me on this?

Hello looking for advice please. My dellorto carb is badly worn and has float issues. I have a mikuni vm 26 in the garage in a 4 stroke pitbike. Could it be re jetted to work in the gas gas txt pro (2009) Thanks in advance

I bought a 2013 TXT 280 about 6 months ago. I am new to anything related to trials bikes. Anyone know why the bike would have a slight grinding sound when the motor is running in neutral? I doubt the bike has many hours on it, as it looks showroom new. Thanks,

Apologies I know this is most likely a stupid question... I'm changing the oil in the forks, I have started with the right side rebound leg, is there anything else I need to do other than set the correct oil height? Do I need to do anything with the damper circuit? Then I guess same question with the compression side? I have read all the posts here on the topic but am still a bit confused, I have the document from the hell team also but still don't fully understand if the complex bleeding applies to me if I'm just replacing the oil in the lowers. Thanks in advance. Gary

Hello, does anyone know how much torque is necessary for head bolts when replacing top end on a Gas Gas txt 280 2014? Would appreciate any expertise! Any other advice when replacing will not fall on deaf ears. Thank you much!

Hi, I have just bought a 2003 Pampera mk3 and it has a really stiff and notchy gear change. It’s the same engine as fitted to the early non-Pro TXT’s. Can anyone advise on possible cause and fix for this? The shaft doesn’t appear to be visibly bent from initial inspection (without removal). I have drained the oil (which was low) and filled with 650ml Putoline Light Gear Oil which hasn’t made an initial difference.

I have a 2022 125cc GP. The last trial I rode at the weekend. The clutch got very heavy to pull in. And then it would get light again, the clutch still worked OK either way. What would cause this or is it normal.

Looking for one, anyone got one sitting on the shelf?

Model: GasGas TXT Racing 125, 2018 Carb: Dellorto PHBL 26 BS I have just bought this bike & am struggling to adjust the carb so that it runs cleanly. The fuel screw needs to be quite far out (4.5 turns) to get it to start reliably, & the idle itself sounds fine, but off-idle (bottom 1/8th throttle) doesn't pick up clean with this setting & the needle in standard position (3rd from top clip). If I drop the needle the pickup cleans up a bit, but at any needle setting the engine sounds raggy at around 1/4 throttle. Returns to idle ok & w/o pinging. Fully open it sounds fine. Jetting is I think standard, but the needle looks scored & doesn…

The idle speed on my newly purchased 2018 TXT Racing goes down when the fan kicks in. Is this normal or an indication of an electrical issue? Any advice appreciated.

Hi have recently destroyed my carbon airbox on my 2018 250 gp, and was wondering whether a plastic one of a 2022 model would fit as I've got an opportunity to buy one at a good price👍

Hello. Can someone please tell me what temperature the stat should cut in and out at. I am using the stat in the top of the radiator but a previous owner has also fitted an inline one. My cylinder head always holds around 60 degrees c with the radiator stat. The fan is running quite a bit to hold the 60 degrees. Thank you in advance

Hi all, 1st post for a few years!!. Does anyone have or know where to get a replacement original Gas gas rear trials light as per my photo ? Just want as per original not a generic one..... Cheers S_M

Prior to the 30c+ hot weather we've had recently my bike was running perfectly. Carburation was spot on. The last 2 trials have been in very hot weather and on tcikover the bike has started hunting a bit like it's running low on fuel. If I rev it then it's ok again for a few seconds then it starts picking and hunting again. The last trial I went to adjust the air mixture screw and found it was only half a turn out (I've not touched it in the 6 years I've had the bike, a 2014 300 Racing). Screwing it right the way in helped but not enough to completely eliminate the issue. What else can I do? Is there potentially a blockage somewhere? Do they do different air mix…

Hey there. I'd like to upgrade the steel front axle in my 2020 to the aluminum one that's on the 21 and 22. Does anyone know if it's a direct fit? Thanks, Joe

Hello. I have recently removed this 6002 rs bearing with great difficulty.... I am now trying to install a new bearing. I have tried the heat freeze method but it won't work for this bearing. I've had the case at 130 degrees and the bearing in the freezer overnight.... I have now got to the point of heating the case and gently trying to press the bearing in. The problem is it starts to go slightly out of alignment no matter what I seem to try. I can measure 1 mm difference accross the bearing. I'm looking for some advice please 🙏 thank you very much

Can anyone tell me the age of this bike

Hi all does anyone know where I could get some swing are pin rubber bungs from ?

So my 2014 GasGas has developed a very annoying creaking noise which is very difficult to locate precisely. Even the slightest movement pushing down on the footrest makes it creak. It's definitely not a squeak and sounds more like dry plastic rubbing than anything else I've taken the rear shock out and the swinging arm moves up and down smoothly with no noise. Similarly the dog bones move freely with no noise. Thinking it could be the shock itself I've removed the spring but the piston shaft moves freely (with a firm push) with no noise (also had it refurbished about 2 years ago with little use since). What on earth could it be? Open to trying anything as its …