Montesa

Hi, yhis is my first post as you can prob already see that! anyway hello all.............. The other day i somehow managed to crack my front caliper through the middle into 2 peices!! qustion is.......Is there an uprade for the bike? i could also do with a disc,Can anyone point me to a supplier for a 4 pot conversion or just the standard, even second hand? please help me.........

I have a 1999 montesa 315r and I am not impressed with the front brake performance. I have read some discusions on this website pertaining to getting the 2 pot brake better. I recently saw a '97 315r for sale that had stock forks and a 4 pot brake mounted. When I went to email the owner it was gone and the listing was deleted. What I would like to know is if the 4 pot is a direct bolt on? Will it line up with the disc?

Hi all, I've had a '99 Cota 315r for a few years now and it's served me well, but recently I've been having trouble running it. It starts up (with choke on) fairly easily, and warms up like normal on choke, but when I take it off choke it idles for about 2 minutes, then just cuts out. I can keep it running by constantly revving it, but when I go back to idle it stalls. I've tried setting the idle higher (it's about as high as it can realistically be at the moment) and no change. I've cleaned out the carb recently, and changed the spark plugs. If anyone has any advice, it would be most appreciated. Thanks Chez.

Hi all, My Mont is almost ready! After a 6 month lay-off to fit a new kitchen, move house then decorate the new house I finally found time to get into the garage and fettle the old girl! Aktive reed valves. Chrome down pipe. Rear suspension bearings all renewed. New back tyre. New Air filter. Oil change. .....and a good clean up! Note: Still got the footpegs to clean up/paint. She's already had a 4-pot caliper fitted up fornt, a straight pipe fitted to the silencer and the timing advanced. This old 1999 Mont is NOT short of power. PS. The chrome downpipe from Sandifords had the restrictor welded in place.....had to drill it out with a hole cutter. Ian.

Can anyone please help me get a flywheel puller for my montesa.Been looking for weeks,I got one.A right dodgey on.Thearded the puller???

I recently purchased this montesa it's my first ever trials bike. I recently bought lights to fit to make it road legal how do i wire them up ready to get a night time mot? Thanks lads.

Hi does anyone know how much a 1999 montesa cota 315r was when it first came out? thanks in advance for replies Tom

hello my montesa cota 315R has been recently giving me trouble with the clutch. whenever i put it into gear it starts to move like when you let the clutch of but im stull holding the clutch in and i have to give it some throttle or it will cut out and when im stoping the bike to put it out of gear whenever i pull the clutch in it doesnt do anything and it stolls. i recently got it serviced and all the oils changed. i had troubles with it before i had it serviced but it worked fine for about a week after i got it back and then the clutch started doing that thing again. the bike is a 1999 montesa cota 315R and if any one can tell me what they think is rong that would be a b…

1st gear on the 4ride,standard 10/41 gearing,is the same as 2nd gear on the 4rt on 10/41 gearing. My question is if you ride a Montesa 4rt on 10/41 gearing what would you use 2nd gear for.

Hi there need help please looking for a titanium front pipe for my montesa 315

Got my 4rt last week(Illinois) and had a chance to ride it saturday. the ground was frozen and temps around 28F sold a 04 Raga replica to get the 4rt 4rt feels heavier for sure- because it is! starts beautifully and runs the same I am an advanced level rider in our area with limited hopping ability(Very limited!!) things seem to happen slowly on this bike right away I felt in control ( I never gelled with my Raga so I sold it-Pretty sure it was just to radical for my ability) all the normal obstacles I tried I was able to due with ease even though I felt I was going to slow off cambers were much easier as traction for me was far better then my Raga and wher…

I have changed my decompressor so it barely opens,will my 349 Cota start if I setup that way? previously it opened to far and the bike won't start as I think not enough compression?,anyone working this way As i'am going more trail than trials I would like to fit a headlight,I see a cut black/white wire off the coil wire and presume that's a 12v from the charging system which I again presume is a 12v DC dynamo ??? ,can I run a headlight off that?,if DC I won't need a rectifier correct? (thinks that's right) as most newer bikes are AC. Have found a semi period correct headlight which should do for my needs.

With the production of the CRF 150 r does that mean that Montes Honda will be bringing out a 125 4rt?????????????

Has anyone got any of the maps that is compatable with the 2 stage throttle body as the standard maps are not compatable. If so any chance you could email me?

AS ANY ONE PUT A 2 STROKE ENGINE IN 4RT FRAME?

I have a montesa 315r with a slight bend in the header pipe and it doesn't quite seal on one side when bolted on what sealant can i use on the joint where the exhaust connects to the cylinder? Thanks in advance

hello this question mite be a no brainer for some of yous but where do i get engine oil for a 2 stroke montesa. i dont need the oil for the petrol mix just the oil for the engine. if you can tell me where to get it that would be a big help. thanks jordan

can anyone help me? black oil comes out of the first exhaust joint on my 2001 montesa 250. I am running it on 50;1 Rock oil 2 stroke , is this right? Also I have no way of knowing how much gear oil to put in, Could too much damage it?

Currently riding a Sherco 290 2012 the last of the stop machines.I ride at clubman level, down south, to be honest I find it can be bit of an handful i.e. gets away from me in the technical stuff , I have had a quick go on a 2016 4RT, it is heavier especially the front end although I found the power delivery very linear and precise which was great but I'm just wondering how big a learning curve it will be to change to a 4 stroke ?

Hi, can anybody advise what is a decent aftermarket clamp set that will fit the Cota 200?? Had a look on Renthal site, but nothing listed for 200 Cota. Thanks