Jump to content

scorpa250

Members
 View Profile  See their activity

  • Posts

    238

  • Joined

  • Last visited

 Content Type 

Everything posted by scorpa250
 
 
  1. scorpa250

    Montesa 348

    scorpa250 replied to scorpa250's topic in Montesa

    I did , find one on ebay
  2. scorpa250
    Great looking 200 you should have a lot of fun on that beauty !!
  3. scorpa250
    I tried one on my Fantic 300 ,Could not get it to run right afer lots of jet changes ( and i was meant to come ready to go) Fitted a Flat slide dellorto and one jet change and spot on . Have the same 26mm VHST on my other bikes Great carb a little expensive but so is buying a OKO and it not working !!
  4. scorpa250
    Yes you need to remove the flywheel , and the inner case then you can see the screw
  5. scorpa250
    Remove the flywheel cover and in the top left hand side is a slotted screw remove that and you can now pull out the clutch arm, on the bottom corner is where the push rod makes contact . remove the large center screw in the clutch cover and you can access the push rod this end , you should be able to see if there is a problem .
  6. scorpa250
    Go onto Beta uk look up the year you think and the frame and engine numbers on there you may have to try a couple of years to get the correct year , One wheel is wrong colour
  7. scorpa250
  8. scorpa250
    Not mine but a good image of the inside of a 301 exhaust
  9. scorpa250
    Back in the 80's when the Michelin soft compound came out one of the other tyre makes used to soak the rear tires in mentholated spirit
  10. scorpa250
    That is a genuine majesty , have a look on the base gasket area and see if there is a spacer about 5mm thick if so 200 majesty . Well done dont see many original ones anymore .
  11. scorpa250

    Majesty Rear Wheel

    scorpa250 replied to mur's topic in Yamaha

    Dished sprocket only used on the 250 twinshock
  12. scorpa250

    Majesty Rear Wheel

    scorpa250 replied to mur's topic in Yamaha

    Same Wheels on both
  13. scorpa250
    Shared on facebook trials pages
  14. scorpa250
    The TLM 260 was not produced in 87 when the test took place ..
  15. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    Hi czrider have you had any luck sorting the problem out ???
  16. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    If i open the bleed screws and leave loose no problem , So why when tight the air pressure keeps going up until it forces oil past the seals ? release pressure and no leaks . action of forks are good
  17. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    No Same springs as before
  18. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    My 300 Made up from spares in the shed from a few fantic's i have collected over the years not a looker a Rider
  19. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    No not that , i cant get my head round it ???????????
  20. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    No all standard in side the legs, i had a montesa that used to hiss when compressing the legs . I have had in excess of 15 fantic's and never come across this before .
  21. scorpa250

    Fantic Forks

    scorpa250 replied to scorpa250's topic in Fantic

    The correct amount 220ml
  22. scorpa250

    Fantic Forks

    scorpa250 posted a topic in Fantic

    Hi I just put together a set of 35 mm fantic forks for a bike i am doing ( new legs new seals and springs ) Put in the bike felt ok but one leg started leaking ?odd i thought i may have caught a seal so i replaced seal and tried again ..same again . so i took the little screw out of cap and there was a woosh of air .. so i took the caps apart made sure the air hole was clear put back in and went for a ride under hard compression oil came out the little air hole ?? Help Please ..
  23. scorpa250
    Hi topcat it is on the front downtube , is it the box that gives trouble?
  24. scorpa250
    Hi all, as the title says a friend of mine has a TLM 260 which has all of a sudden lost its spark Is there a common problem as I seem to remember reading this before for this model ?? Is it possible to have the CDi checked ?? Thanks .
  25. scorpa250
    Hi all , Whats the cost of re-plating a worn trials cylinder these days ?? ( fantic 300) Thanks .
 
×
  • Create New...