Fantic

Fantic 200 Minarelli. Have a slight oil leak from where the small push rod enters the caseing. Understand there's an O ring on that rod, and want to change it and hopefully stop the leak. Problem I have is I can not get the rod out. Can get it to poke its noise out with a magnet then grab it with some small pliers but can't get it out. Am I not trying hard enough, or have I missed something? Thanks.

Hi all any input would be appreciated. Fantic 200 1980, front brake drum badly worn, looks like somethings been in there at some time and worn a trench in it must be 15mm wide x 4mm deep. Can these be relined or milled/bored out?

I've been offered an air-cooled 125, the seller says it's a 1992 model , 240 I understand. Are there any particular problems with these? Thanks

What is the premix ratio for the 2022 xe 125 please

Hello everyone, I'm rebuilding a 35mm Marzocchi fantic 200 fork, I want to change the internal friction bushings but I can't find the same size. any idea? thanks in advance

Got a 1984 fantic 240 and it's always had weak brakes. Just put new shoes new cable and lever on it but it has made little difference. I've tried to leave everything loose cable tie the brake on and then tighten everything up but still the brakes are weak. The brakes bite but the lever still feels spongey and pulls nearly all the way to rhe bars after it bites. I've seen on here somewhere that the centre hole on the backing plate can be opened by 0.5mm ish to help centralise the the shoes in the drum. Is this my best chance of getting better brake performance before I go and enlarge the hole? Thanks for any replies!😁

On occasion my Fantic 200 rear kick jumps out of bottom gear. I have been advised it's likely to be the spring holding the location bearing under the selector drum. I have stripped the engine and removed the gear cluster and inspected all components, no obvious damage , gears and dogs are sound and no selector fork damage. I wish to replace the spring in case it's worn , but how do I find a replacement, does any one have a spec or a source, I believe there is no official stock left Any suggestions

Hi guys Can anyone help me with standard Inlet, Transfer and Exhaust duration in crank degrees of the 212cc engine? Thanks in advance, Prelit.

Hi, I am going to replace the carb on my 300 Pro. Dell Orto PHBH26BS, I've been checking prices online and the cheapest genuine one is from a scooter shop. Just looking for confirmation that they are all the same dimensions, cheers

1993 Fantic Kroo 249 with the leaking seal in clutch slavecylinder. Where can I find new seal? Lever cup says dot4, is it right? Lever is not original and have no idea what previous owner has put in there.

Hi new to this website, picked a v vintage Trials bike and trying to figure out year, model and make. I'm into vintage MX bikes, but dont know much about Trials bikes. Does anybody know what this bike is? Thanks!

Afternoon, Anyone know where I can get a new brake cam? Grimeca 125mm, Fantic 200, the thread has practically worn away. I could turn it down in the lathe and thread it 6mm but I'd prefer a new one really. Cheers in advance.

Is there an extended seat available for the 305 or anyone been able to build one and can share design?

Hi , just wondered what everyone is running? My bike has come with 11/56 which makes it pull well in 2nd and 3rd. im looking at new sprockets and 56 renthal doesn’t seem available, in motion stock 53 and Bill Pye says he runs his bikes on 11/52 cheers

Hi, I've bought a Fantic, which seems to be a bitsa - I was told by the seller it is a 245 with K-Roo bottom end, which is why it has a hydraulic clutch. I bought it knowing the clutch slave seal is goosed. I didn't realize the slave is inside the engine. But, the seller issued me with another set of 212cc crank cases which have the cable type of clutch and advised me to swap the internals into these cases. Does this sound doable, please? I'll try to post some pictures. Regards, Rab

i am just about to take a pair of 247 USD trials forks apart to replace the seals, are they quite easy to take apart and are there any tips to help ?? Ive taken loads of std forks apart, just non of the USD ones. And anyone know where i can buy the seals from?

Hi all, I’m new here but have a nice little 200 that needs some tidying . it came with betor forks which don’t seem common on uk bikes, I believe the bike came from Holland but no one in the know has seen internals like them, one thing is they are super plush. I’ve seen another pic with them on but wondered if it was just a batch they had or if someone added them later for whatever reason. thanks

Can anyone tell me if these are the same, I thought the way the brake plates were held in place was different for a start and I would have thought some dimensions between the two would differ also. Thanks.

Can anyone help with rim offset for the FM350 Minarelli 156 and the FM250 125 Professional please?

I've got the FM236 special (alloy rims and skidplate) , But Man ...A Fantic lawnmower and my collection would be complete (for now.) Could their diversification been part of their downfall ??? They still make highend coffee machines though ....