Scorpa

Can any body tell me how to take the cylinder head off the sy? I've striped bike down rad off ECT the head steady is stoping the head coming off I was hoping to get away from taking the motor out is there a nack am I missing something? I want to replace the small end bearing am not new to striping and rebuilding bikes just never done a scorpa before I have the New parts to hand to do the work so frustrating. Cheers

Hi everyone! Having some problems with my 06 Scorpa SY250. During a riding session, I wheelied the bike out on a steep hill section causing it to land hard on the right handle bar twisting the throttle cable completely around the handlebar. Prior to realizing that the cable was out of place, the bike was started, initiating an out of control idle climb that ended in a very loud backfire when the fuel line was closed because the kill-switch would not cut it off. Once the cable was returned to its original position, the bike started and ran, however it had extremely poor throttle response. So my thought was to change out the throttle cable, which in turn did not c…

Hello All can some 1 tell me witch packing do you use to repack the sy silencer? Pad tho or the loose stuff? Also is it worth doing the bike is running ok I've just striped it down to clean the carb and I've flushed the exhaust I've put a brand New front pipe on it also.

What would cause this

New bike and wow how good is it ( ability of the bike is far higher than the operator!). Decided I wanted to monitor engine temperature and keep track of my engine hours, fussy. Trail Tech temp gauge left over from my KTM 500 exf with the radiator fin option (10mm) so considering the radiator fins are no where near this, used JB weld to glue the sender into position on the radiator header tank at coolant level. Several options for the temperature sender are available. Fan comes on at 61 degrees C, max temp the other day was 73 degrees C plodding around in ambient 25 degrees C, wonder what it goes up to on our 43 degrees C days we had 2 months ago. Good guide to see wh…

can anybody tell me how to get the front L/H slotted bolt out? i cant get a Allen key to in to undo it is there a knack to do it cheers.

Not a bad effort on the first day of the SSDT with 3 Scorpa's in the 6 clean sheets on day 1 Bet Mr Birkett was smiling last night

should there be any kind off rubber under the fuel tank?

Looking for a new silencer for a SY250 OEM or aftermarket? This seems to be a problem for an older model bike, it is quite noisy somone has tried to repack it before, not done a great job There seems to be a lot of SY250 still about, all getting louder, somone must make them?

hello as any 1 had problems with the rear sprocket bolts? i just got a new s3 sprocket and the bolts stick out to much there is a shallow recess not counter sunk any ideas what bolts i can use? i do have domed bolts but not sure if they will catch the S/Arm

Hello, I have a Magura mount on my TY, need to replace the oil tube because is damage and it lack. I can't found any information about it. Is it a standard 163 Hymec | 167 Hymec | HC3 tube? (Magura code 0722137) Seems not standard to other clutch tubes Hope in a help Thanks

Hi all help needed please . recently brought a 2016 scorpa 250 ,only owned about a month but have developed a running issue , it cut out on me last week and wouldn’t start so cleaned out carb fitted new fuel filter started fine then after about 15 min started hunting / spluttering then cut out again . Don’t know if it’s sucking in air or fuel starvation , can see fuel in filter .does anyone know what are correct jets and settings are for carb ? wanted a good bike to get back into trials but this is doing my head ,

can any 1 tell me what the torque is for the 2007 scorpa sy rear wheel nut? looked up and it says 60NM?

Hi guys can anybody tell me where I can get the wider bash plate for the scorpa sy 2007?

When I got this SY, there was evidence of the previous owner burning traces of riding gear onto the exhaust headpipe. During my informal dismantle and reassembly, I scrubbed that headpipe to remove all traces of burnt on gear, oil spooge stains and carbon builup at the headpipe slip joint into the exhaust mid box. After several hours of riding the SY, it was apparent that even I was leaving burnt riding gear traces onto the headpipe. Being frugal, I waited on some leftover high temp epoxy, then rounded up some scraps of carbon cloth. In a short bit of time, I fabricated my copycat heatshield. Mounting is simple, two high temp silicone bands between the ca…

Minor change, but does make things easier.

What Size rear sprocket you guys running on the scorpa sy? what is the STD And what is the norm am not sure what's on it at the moment but its not very big

Can any 1 tell me what the bolt is under the front sprocket looks like a drain bolt it as a copper washer

i am impressed by the 4 storke scorpa as its well nice but has any body seen one before

Hi everyone! I've completely stripped the carb on my SY250 to give it a good clean. However, since coming in from the garage to eat tea, put small dude to bed etc. I can't remember how the needle/ throttle slide assembly goes back together. There's a small washer with a tab/tang on it, does this go underneath the needle clip (between circlip and throttle slide) or on top of the needle clip (between circlip and retaining plate assembly)? Hope this makes sense and that someone can help!